Low Load Solenoid Valve Kit - Installation

Last updated: 02/18/2022

طقم صمام التحميل المنخفض - تركيب

AD0594

مقدمه

This procedure outlines how to add in an AC input line filter to the I/O PCB and solenoid output filter. These kits will assist intermittent SMC solenoid related alarms.

Machine Requirements:

I/O PCB P/N 34-3490 or later

This procedure applies to the following kits:

93-3450: DUAL SOLENOID FILTER SERVICE KIT
93-3451: SINGLE SOLENOID FILTER SERVICE KIT
93-3452: SIO PWR FILTER SERVICE KIT

التثبيت

1

Push [POWER OFF].

Set the main circuit breaker to the [OFF] position.

Lock the main circuit breaker. Use an approved lock with an approved safety tag.

Danger: After turning off the machine, wait at least 5 minutes before working in the control cabinet, to allow power to dissipate. Wait for the voltage indicator LED on the vectore drive to go off completely.

Caution: When you handle a PCB, you must wear an Electrostatic Discharge (ESD) strap.

2

للماكينات التي لا تحتوي على لوحة لمبدلات الأدوات

قم بتركيب لوحة SIO بالجانب الأيسر من لوحة الإدخال/الإخراج باستخدام القوائم والمسامير المرفقة.

افصل الكابل 33-0349 من P55 على لوحة الإدخال/الإخراج وقم بتوصيله بوصلة الإدخال الخاصة بلوحة SIO [1].

قم بتوصيل الكابل من لوحة SIO إلى P55 على لوحة الإدخال/الإخراج [2].

للماكينات التي تحتوي على لوحة لمبدلات الأدوات

قم بتركيب لوحة SIO بالجانب الأيسر من لوحة لمبدلات الأدوات باستخدام القوائم والمسامير المرفقة.

افصل الكابل 33-0349 من P55 على لوحة الإدخال/الإخراج وقم بتوصيله بوصلة الإدخال الخاصة بلوحة SIO [3].

قم بتوصيل الكابل من لوحة SIO إلى P55 على لوحة لمبدلات الأدوات [4].

3

For Solenoids in the Lube Panel

In the lube panel cut off the air supply and bleed the excess from the air gun.

Disconnect the SMC solenoid [1] from the lube panel connection.

Attach the SMC solenoid to the solenoid filter [3] and attach the solenoid filter to the lube panel connection [2] that the SMC solenoid was previously disconnected from.

Note: Pictured is a single SMC solenoid using a single soleniod filter, same process can be used for the SMC double solenoid by using a double solenoid filter.

4

For Solenoids in the Lube Panel

Use zip ties to secure the solenoid filter in the cable channel as shown in [1] & [2].

Cut the excess off the sip time and put any excess wire lengths in the cable channel and slide the cover up as shown in [3].

5

APL Solenoids

Disconnect the APL solenoid [1] and connect it to the double solenoid filter [2] connection [3] that was ordered.

Connect the solenoid filter where the APL solenoid was originally connected to [4].

Zip tie the double solenoid filter to the mounting bracket as shown [5].