Početna stranica za servisiranje Upute za izvršenje Krovni izmjenjivač alata - 20/32 - Džep karusela - Motor - Zamjena - AD0295
Last updated: 04/07/2021

Krovni izmjenjivač alata - 20/32 - Džep karusela - Motor - Zamjena

AD0295

20/32 - Pocket Carousel - Motor - Replacement - Introduction

This procedure tells you how to replace the carousel motor on a 20- or 32-pocket umbrella tool changer, and a GR machine with a 10-pocket umbrella tool changer.

  1. carousel motor power cable
  2. tool-in-position limit switch
  3. tool-1-in-position limit switch
  4. carousel motor

Machine Compatibility

All VMCs

Requirements:

  • VMCs with a 20/32-pocket umbrella tool changer
  • GR machines with a 10-pocket umbrella tool changer, use [KIT] 30-2416

Document Applies to these Parts

This procedure applies to (6) different kits. You only need (1) motor assembly to complete the procedure.

[KIT]

30-2416

QTY: 1

MOTOR, UMBRELLA CAROUSEL 10 POCKET W/ MECH SENSOR (GR & SMM)

[KIT]

93-7000

QTY: 1

MOTOR, UMBRELLA CAROUSEL 16 / 20 POCKET W/ MECH SENSORS (SINGLE PIN DRIVE)

[KIT]

30-0005

QTY: 1

MOTOR, UMBRELLA CAROUSEL 20 POCKET W/ MECH SENSORS(DUAL PIN DRIVE)

[KIT]

93-30-0005A

QTY: 1

MOTOR, UMBRELLA CAROUSEL 20 POCKET W/ PROX SENSORS(DUAL PIN DRIVE)

[KIT]

93-1685

QTY: 1

MOTOR, UMBRELLA CAROUSEL 32 POCKET W/ MECH SENSORS (DUAL PIN DRIVE)

[KIT]

30-0016

QTY: 1

MOTOR, 50T UMBRELLA CAROUSEL 20 POCKET W/ MECH SENSORS

Umbrella Tool Changer - Pocket Carousel - Motor - Replacement

1

Push [POWER OFF]. Set the main circuit breaker to the OFF position.

Lock the main circuit breaker. Use an approved lock with an approved safety tag.

2

Remove the (4) screws [1] that attach the cover panel [2] to the tool changer carriage. Remove the cover panel [2].

 Note: 10-pocket carousel motor covers have the screws on the back of the tool changer carriage.

Disconnect the carousel motor cable, the tool-in-position cable, and the tool-1-in-position cable [3] from the electrical bracket.

Remove the (4) screws [4] and (4) washers [5] that attach the carousel motor assembly [6] to the bottom of the tool changer carriage. Remove the carousel motor [6].

3

Attach the new carousel motor assembly [1] to the bottom of the tool changer carriage. Use the (4) screws [2] and (4) washers [3].

Connect the carousel motor cable, the tool-in-position cable, and the tool-1-in-position cable [4] to the electrical bracket [5].

Install the cover panel [6] to the tool changer carriage.

Unlock the main circuit breaker. Set the main circuit breaker to the ON position.

Push [POWER ON]. Push [POWER UP/RESTART].

Make sure the umbrella tool changer rotates.

Obavijest o kolačićima

Kolačiće koristimo za poboljšanje vašeg korisničkog iskustva. Naša obavijest o kolačićima opisuje koje kolačiće koristimo, zašto ih koristimo i kako možete pronaći dodatne informacije o njima. Potvrdite svoj pristanak za naše korištenje analitičkih kolačića. Ako ne pristajete, i dalje možete koristiti naše web-mjesto uz lošije korisničko iskustvo.