×

Arama Sonuçları

Web Pages

Images

    • <
    • 1
    • >
  • tezgahlar
    • Haas Dik Frezeler
      Dik Frezeler
      • Dik Frezeler
      • VF Serisi
      • Üniversal Makineler
      • VR Serisi
      • Palet Değiştiricili VMC’ler
      • Mini Frezeler
      • Kalıp Makineleri
      • Delme / Kılavuz Çekme / Frezeleme Serisi
      • Takımhane Frezeleri
      • Kompakt Frezeler
      • Gantry Serisi
      • Dik Freze/Torna
      • Ekstra Büyük VMC
      • Çift Kolonlu Frezeler
      • Masaüstü Freze
      • Freze Otomatik Parça Yükleyici
    • Product Image
      Çok Eksenli Çözümler
      • Çok Eksenli Çözümler
      • 5-Eksenli Frezeler
      • Y Eksenli Tornalar
    • Haas Tornalar
      Tornalar
      • Tornalar
      • ST Serisi
      • Çift İş Mili
      • Takımhane Tornası
      • Aynalı Torna
      • Haas Çubuk Sürücü V2
      • Torna Otomatik Parça Yükleyici
    • Haas Yatay Frezeler
      Yatay Frezeler
      • Yatay Frezeler
      • 50 Konikli
      • 40 Konikli
    • Haas Döner Tablalar ve İndeksleyiciler
      Döner Tablalar ve İndeksleyiciler
      • Döner Tablalar ve İndeksleyiciler
      • Döner Tablalar
      • Divizörler
      • 5 Eksen Döner Tablalar
      • Çok Büyük Döner Tablalar
    • Product Image
      Otomasyon Sistemleri
      • Otomasyon Sistemleri
      • Robot Sistemleri
      • Otomatik Parça Yükleyiciler
      • Palet Havuzu Sistemleri
      • Haas Çubuk Besleyici
      • Models
    • HIZLI BAĞLANTILAR Özel Seri  Özel Seri 
      HAAS KARİYER HAAS KARİYER OLUŞTUR VE FİYAT AL OLUŞTUR VE FİYAT AL FİYAT LİSTESİ FİYAT LİSTESİ YENİLİKLER YENİLİKLER İLK CNC’NİZ İLK CNC’NİZ HAAS ALTILI PAKET HAAS ALTILI PAKET
      ALIŞVERİŞ ARAÇLARI
      • Bir Haas Oluştur ve Fiyat Al
      • Fiyat Listesi
      • Mevcut Stok
      • CNCA Taksit Seçenekleri
      BİR YETKİLİYLE Mİ GÖRÜŞMEK İSTİYORSUNUZ?

      Haas Fabrika Satış Mağazası sorularınızı yanıtlayabilir ve size en iyi seçenekleri sunabilir.

      CONTACT YOUR DISTRIBUTOR >
  • Seçenekler
    • Product Image
      İş Milleri
      • İş Milleri
    • Product Image
      Takım Değiştiriciler
      • Takım Değiştiriciler
    • Product Image
      4. | 5. Eksen
      • 4. | 5. Eksen
    • Product Image
      Taretleri ve Tahrik Takımı
      • Taretleri ve Tahrik Takımı
    • Product Image
      Problama
      • Problama
    • Haas Talaş ve Soğutma Sıvısı Yönetimi
      Talaş ve Soğutma Sıvısı Yönetimi
      • Talaş ve Soğutma Sıvısı Yönetimi
    • Haas Kontrol Ünitesi
      Haas Kontrol Ünitesi
      • Haas Kontrol Ünitesi
    • Product Image
      Ürün Seçenekleri
      • Ürün Seçenekleri
    • Product Image
      Takımlar ve Fikstürleme
      • Takımlar ve Fikstürleme
    • Product Image
      İş Parçası Bağlama
      • İş Parçası Bağlama
    • Product Image
      5 Eksen Çözümler
      • 5 Eksen Çözümler
      • 5 Easy Steps to 5-Axis
    • Product Image
      Otomasyon
      • Otomasyon
    • HIZLI BAĞLANTILAR Özel Seri  Özel Seri 
      HAAS KARİYER HAAS KARİYER OLUŞTUR VE FİYAT AL OLUŞTUR VE FİYAT AL FİYAT LİSTESİ FİYAT LİSTESİ YENİLİKLER YENİLİKLER İLK CNC’NİZ İLK CNC’NİZ HAAS ALTILI PAKET HAAS ALTILI PAKET
      ALIŞVERİŞ ARAÇLARI
      • Bir Haas Oluştur ve Fiyat Al
      • Fiyat Listesi
      • Mevcut Stok
      • CNCA Taksit Seçenekleri
      BİR YETKİLİYLE Mİ GÖRÜŞMEK İSTİYORSUNUZ?

      Haas Fabrika Satış Mağazası sorularınızı yanıtlayabilir ve size en iyi seçenekleri sunabilir.

      CONTACT YOUR DISTRIBUTOR >
  • Why Haas
      Haas Farkını Keşfedin
      Neden Haas MyHaas Eğitim Topluluğu Endüstri 4.0 Haas Belgesi Müşteri Tanıklıkları
  • Servis
      Haas Servisine Hoş Geldiniz
      SERVİS ANA SAYFA Operatör El Kitapları Nasıl Yapılır Prosedürleri Sorun Giderme Kılavuzları Önleyici Bakım Haas Parçaları Haas Tooling Videolar
  • Videolar
  • MyHaas – Her Şey için Tek Yer

    • Compare Quotes
      • Compare Quotes

    • MyHaas Hakkında
      • MyHaas Hakkında

    • Haas CNC Sertifikasyon Programı
      • Haas CNC Sertifikasyon Programı

    • Haas CNC Certification Program-Redirect
      • Haas CNC Certification Program-Redirect

    • Haas CNC Sertifikasyon Programı
      • Haas CNC Sertifikasyon Programı

    • Haas Learning Resources
      • Haas Learning Resources

    • Haas Global Learning Resources
      • Haas Global Learning Resources

    • MyHaas App Form
      • MyHaas App Form
    • HIZLI BAĞLANTILAR Özel Seri  Özel Seri 
      HAAS KARİYER HAAS KARİYER OLUŞTUR VE FİYAT AL OLUŞTUR VE FİYAT AL FİYAT LİSTESİ FİYAT LİSTESİ YENİLİKLER YENİLİKLER İLK CNC’NİZ İLK CNC’NİZ HAAS ALTILI PAKET HAAS ALTILI PAKET
      ALIŞVERİŞ ARAÇLARI
      • Bir Haas Oluştur ve Fiyat Al
      • Fiyat Listesi
      • Mevcut Stok
      • CNCA Taksit Seçenekleri
      BİR YETKİLİYLE Mİ GÖRÜŞMEK İSTİYORSUNUZ?

      Haas Fabrika Satış Mağazası sorularınızı yanıtlayabilir ve size en iyi seçenekleri sunabilir.

      CONTACT YOUR DISTRIBUTOR >
  • İletişim

My Cart
MyHaas Hoş Geldiniz,
!
Haas Tooling Misafir Sipariş Geçmişi MyHaas/HaasConnect Oturum Aç Kaydol Haas Tooling Hesabım Order History Return History MyHaas/HaasConnect Oturumu Kapat Hoş Geldiniz, Makinelerim Son Etkinlik Fiyat Tekliflerim Hesabım Kullanıcılarım Oturumu Kapat
Bir Bayi Bul
  1. Dil Seçenekleri
    1. English
    2. Deutsch
    3. Español - España
    4. Español - Méjico
    5. Français
    6. Italiano
    7. Português
    8. Český
    9. Dansk
    10. Nederlands
    11. Magyar
    12. Polski
    13. Svenska
    14. Русский
    15. Türkçe
    16. 中文
    17. Suomi
    18. Norsk
    19. الإنجليزية
    20. български
    21. Hrvatski
    22. Ελληνικά
    23. Română
    24. Slovenský
    25. Slovenščina
    26. 한국어
    27. 日本語
Search
×

Arama Sonuçları

Web Pages

Images

    • <
    • 1
    • >

Pallet Pool - NGC - Troubleshooting Guide

Servis Ana Sayfa Palet Havuzu - Sorun Giderme Kılavuzu - NGC
Recently Updated Last updated: 01/30/2022

Palet Havuzu - Sorun Giderme Kılavuzu - NGC


Palet Havuzu - Sorun Giderme Kılavuzu - NGC

- Nedene Geç - 1. Introduction 2. Symptom Table 3. Lifter Up/Lifter Down I/O Status 4. Load Door I/O Status 5. Electrical Diagrams Back to Top

Introduction

Pallet Pool

  1. Emergency Stop 
  2. Pallet Ready Button
  3. Load Station Door
  4. Load Station
  5. Air Gun
  6. Drip Tray

SENSORS

 
 
  1. PP Lifter Up
  2. PP Lifter Down
  3. PR Axis Home Switch
 
        4. PP Load Door Open
        5. PP Station Lock

 

        6. UMC Pallet Slide Home Switch

         Note: EC-400 Pallet Slide Home Switch is found underneath the ballscrew.

Symptom Table

Symptom Possible Cause Corrective Action

Alarm 15.108 AXIS SERVO OVERLOAD

Alarm 15.103 AXIS SERVO ERROR TOO LARGE

Binding Transmission The amplifier could be having an issue driving the motor. If you have this problem, please contact our service department.

After zero returning the PS or PR axis, the folloiwng alarms are generated:

Alarm 15.103 AXIS SERVO ERROR TOO LARGE

Alarm 16.103 AXIS SERVO ERROR TOO LARGE

Faulty Home Sensor Go to the Diagnostics-MOCON tab, search for PR or PS axis home switch inputs. Manually trigger the PR or PS sensors to verify the bits change states from 0 to 1. If the bits do not change states, use the electrical diagram below to determine which componet has failed.
Hydraulic oil leaks or sprays from the pallet locating pins during a pallet change.   Contact Haas Service.
Alarm 974 Pallet Pool Switch Fault Chips accumulated at sensors. Check the Pallet Lifter Down / Up sensors for chips and clean out any that are found. Recover Pallet Pool and try again. Use the illustrations to locate the sensors.
The pallet pool state proximity sensors are not triggering. Check the Pallet Lifter Down / Up sensor states and make sure the sensors are toggling when triggered. Use the Lifter UP/ Lifter Down I/O Status table below to determine the correct states of the sensor.
Alarm 977 Pallet Pool Lifter Up Time Out Insufficient hydraulic pressure or fluid volume. Make sure the pump is turning on and building enough pressure to lift the Pallet Lifter.
Pallet Lifter was not unclamped. Check for any mechanical obstructions that are preventing the pallet lifter from rising.
Damage to the Pallet Pool up switch or wiring. Check the pallet lifter up and pallet lifter down sensors for proper operation. Use the Lifter UP/ Lifter Down I/O Status table below to determine the correct states of the sensor.
Alarm 9887 Pallet Pool Lifter is Up The Lifter is up when attempting to retrieve a pallet. Enter RECOVERY to attempt auto-recovery, or enter the recovery page to verify that the lifter is operational by commanding it up and down. Check PP Lifter Up (INPUT 38) and verify it is operating correctly. Use the Lifter UP/ Lifter Down I/O Status table below to determine the correct states of the sensor.
Alarm 9888 Pallet Pool Lifter is Down The lifter is down while either retrieving a pallet or placing a pallet. Enter RECOVERY to attempt auto-recovery. If auto-recovery fails, enter the recovery page to verify that the lifter is operational by commanding it up and down. Check  PP Lifter Down (INPUT 41) and verify it is operating correctly. Use the Lifter UP/ Lifter Down I/O Status table below to determine the correct states of the sensor.
Pallet pool is displaying the wrong amount of pallets. Parameter 740 Pallet Pool Max Pallet Count is set incorrectly Change Paramter 740 to the correct pallet count 
Pallet pool up & down solenoid are functioning inversely  Up & down solenoid cables are incorrectly labeled   Order 93-3268 or 93-3268, lower and lift solenoid cable kit for correctly labeled cables. 
Pallet Changer Clamp/Unclamp mechanism operates in reverse. The hydrualic lines are reversed. Check at both ends of the hydrualic lift cylinder and hydraulic power unit and verify that they are set correctly.
The pallet clamp/unclamp sensors are reversed. With a Pallet on the receiver.  Command the pallet to clamp and unclamp.  Go to I/O tab and verify that inputs 25 PALLET CHANGER PALLET UNCLMPED and 29 PALLET CHANGER PALLET CLAMPED toggle to the correct state.  Check the terminal block, check that they are connected correctly.
Alarm 9889 Pallet Pool Slider Door Open Timeout The slider door failed to open within the required time limit Verify there is notthing obstucting the door open switch
Adjust the switch to the flag and make sure it toggles when in position
Check to see if the solenoid is funtioning properly
Verify there is notthing obstucting the door open switch
Alarm 9890 Pallet Pool Slider Door Close Timeout The slider door failed to close within the required time limit
Adjust the switch to the flag and make sure it toggles when in position
Check to see if the solenoid is funtioning properly
Alarm 9892 Pallet Pool Slider Door Not Open  The slider door was detected to be closed when it is expected to be open Check the area around the slider door for obstructions
Verify the correct switch is in the correct location
Alarm 9893 Pallet Pool Slider Door Open  The slider door was detected to be open when it is expected to be closed Check the area around the slider door for obstructions
Verify the correct switch is in the correct location

Lifter Up/Lifter Down I/O Status

Machine State

PP Lifter Up

Input #38

PP Lifter Down

Input #41

PP Pallet Lift

Output #166

PP Pallet Lower

Output #167

Pallet Pool Lifter is Up 1 0 1 0
Pallet Pool Lifter is Down 0 1 0 1

Load Door I/O Status

Machine State

PP  Load Door Open

Input #31

PP Station Lock

Input #33

Door is closed and the station lock is at the home position 0 1
Door is open and the station lock is at the home position 1 1
Door is closed and the station lock is not at the home position 0 0

Electrical Diagrams

Pallet Pool Input Status and Solenoid Output

                                          

PR/PS Switch and Servo Motor Connection to MainCon PCB

DİSTRİBÜTÖR BULUN
Geribildirim
Haas Logo

美元价格不包括关税、报关费用、保险费、增值税及运费。
USD prices DO NOT include customs duty, customs fees, insurance, VAT, or freight.

人民币价格包含关税、报关费用、货运保险和增值税, 但不包括运费。
CNY prices include customs duty, customs fees, insurance, and VAT. DOES NOT include freight.

Haas Teslim Fiyatı

Bu fiyat, sevkiyat bedeli, ihracat ve ithalat vergileri, sigorta ve Fransa’da alıcı olarak sizinle birlikte kararlaştırılan bir yere yapılan sevkiyat sırasında oluşan diğer masrafları içerir. Haas CNC Ürününün teslimine başka hiçbir zorunlu maliyet eklenmez.

EN YENİ HAAS İPUCU VE TEKNOLOJİLERİNDEN HABERDAR OLUN…

Şimdi kaydolun!   

HAAS TOOLING ACCEPTS THE FOLLOWING:

  • Servis ve Destek
  • Sahipler
  • Servis Talep Et
  • Operatör El Kitabı
  • Haas Parçaları
  • Döner Tabla Onarım Talebi
  • Kurulum Öncesi Kılavuzları
  • Alışveriş Araçları
  • Yeni Bir Haas Oluştur ve Fiyatlandır
  • Mevcut Stok
  • Haas Fiyat Listesi
  • CNCA Taksit Seçenekleri
  • Haas Hakkında
  • Kariyer
  • Sertifikalar ve Güvenlik
  • Bizimle İletişime Geçin
  • Geçmiş
  • Hüküm ve Koşullar
  • Haas Tooling Hüküm ve Koşulları
  • Gizlilik
  • Garanti
  • Haas Topluluğu
  • Haas Sertifikasyon Programı
  • Haas Motor Sporları
  • Gene Haas Vakfı
  • Haas Teknik Eğitim Topluluğu
  • Etkinlikler
  • Sohbete Katılın
  • Facebook
  • Twitter
  • Flickr
  • YouTube
  • LinkedIn
  • Instagram
  • TikTok
© 2022 Haas Automation, Inc – CNC Takım Tezgahları

2800 Sturgis Rd., Oxnard, CA 93030 / Toll Free: 800-331-6746
Phone: 805-278-1800 / Fax: 805-278-2255

Çerez Bildirimi

Kullanıcı deneyiminizi iyileştirmek için çerezler kullanıyoruz. Çerez Bildirimi hangi çerezleri kullandığımızı, bunları neden kullandığımızı ve bunlar hakkında daha fazla bilgiyi nereden bulabileceğinizi açıklamaktadır. Lütfen, analitik çerezlerini kullanma konusunda bize izin verdiğinizi onaylayın. Onay vermezseniz, internet sitemizi kısıtlı kullanıcı deneyimi ile yine de kullanabilirsiniz.

Ayarları Yönet

Çerez Bildirimi

Kullanıcı deneyiminizi iyileştirmek için çerezler kullanıyoruz. Çerez Bildirimi hangi çerezleri kullandığımızı, bunları neden kullandığımızı ve bunlar hakkında daha fazla bilgiyi nereden bulabileceğinizi açıklamaktadır. Lütfen, analitik çerezlerini kullanma konusunda bize izin verdiğinizi onaylayın. Onay vermezseniz, internet sitemizi kısıtlı kullanıcı deneyimi ile yine de kullanabilirsiniz.

Functional Cookies

Analytics Cookies