Service How-to-procedure HPC-300-TSC-300-ekstra køling-filter-installation-AD0111
Last updated: 11/06/2020

HPC-300-TSC-300-ekstra kølevands-filter-installation

AD0111

Gælder for maskiner bygget fra: Januar, 1998

Indledning

Denne procedure fortæller dig, hvordan du installerer et finposefilter til kølevand (AF)-system. Dette #2 højtryksfilter fjerner forurening og små partikler fra kølevandet, før de går gennem kølevandspumpen igen.

Denne procedure fortæller dig, hvordan du tilslutter af AF til disse kølevandssystemer:

  • Standard kølevandspumpe [1]
  • Højtrykskøling (HPC)/køling gennem spindel (TSC) 300 pumpe [2] med et sekundært filter
  • HPC/TSC 300/1K med en auto-Clean pumpe [3]

Machine Compatibility:

All machines excluding tool room mills and lathes.

This document applies to the following service kit:

  • KIT PN: 93-1000284, AUXILIARY FILTER KIT

Prerequisites:

Do not apply thread sealant to the hose connections. This makes the hose difficult to remove.

 Note: The illustrations in this procedure show the installed configuration.

Standard Coolant Pump - Installation

1

If the machine has a standard coolant pump:

  • Disconnect the coolant supply hose [1], from the pump outlet [2].
  • Connect the lower supply hose [3] to the coolant supply hose [1].
  • Connect the upper AF hose [4] to the coolant pump outlet [2].
  • Close the machine doors and windows.

 Note: Coolant can splash in the machine.

  • Start the coolant pump.
  • While the coolant pump is on, open the AF lid.

 Note: This pushes the air out of the AF.

  • Close the lid when the AF is full.

HPC/TSC-300 With Sencondary Filter - Installation

If the machine has a HPC/TSC 300 pump with a secondary filter:

  • Remove the coolant return loop [1].
  • Install the coolant hose adapter [A] to the 3/4" NPT port.
  • Connect the upper AF hose [2] to the coolant hose adapter.
  • Connect the 12" (30 cm) pump hose [B] to the 1/2" NPT port in the pump stand.
  • Attach the lower AF hose [3] to the 12" (30 cm) hose [B].
  • Close the machine doors and windows.

 Note: Coolant can splash in the machine.

  • Start the coolant pump.
  • Remove the AF lid while the coolant pump is on.
  • Use the wash gun to fill the AF with the coolant.
    Note: Becareful Coolant can splash at you when using the wash gun.

 Note: This pushes the air out of the AF.

  • Install the lid when the AF is full.

HPC/TSC-300/1K with Auto Clean - Installation

If the machine has HPC/TSC 300/1K and an Auto-Clean pump:

  • Remove the coolant return loop [1].
  • Connect the lower AF hose [3] to the swivel fitting on the outlet pipe.
  • Connect the upper AF hose [2] to the stand pipe [4].
  • Close the machine doors and windows.

 Note: Coolant can splash in the machine.

  • Start the coolant pump.
  • Remove the AF lid while the coolant pump is on.
  • Use the wash gun to fill the AF with the coolant.
     Note: Becareful Coolant can splash at you when using the wash gun.

 Note: This pushes the air out of the AF.

  • Install the lid when the AF is full.

Verification

Operate the standard coolant pump for (5) minutes. Check for leaks.

For maintenance information, refer to Auxiliary Filter - Bag Filter - Replacement.

Cookieerklæring

Vi bruger cookies til at forbedre din brugeroplevelse. Vores cookieerklæring beskriver, hvilke cookies vi bruger, hvorfor vi bruger dem, og hvordan du kan finde flere oplysninger om dem. Bekræft venligst dit samtykke til, at vi bruger cookies til analyse. Hvis du ikke giver samtykke, kan du stadig bruge vores hjemmeside, men med begrænset brugeroplevelse.