MyHaas Καλωσορίσατε
!
Haas Tooling Ιστορικό παραγγελιών επισκέπτη MyHaas/HaasConnect Σύνδεση Εγγραφή Haas Tooling Ο λογαριασμός μου Order History Return History MyHaas/HaasConnect Αποσύνδεση Καλωσορίσατε Τα μηχανήματά μου Τελευταία δραστηριότητα Οι προσφορές τιμής μου Ο λογαριασμός μου Οι χρήστες μου Αποσύνδεση
Βρείτε έναν αντιπρόσωπο
  1. Επιλέξτε γλώσσα
    1. English
    2. Deutsch
    3. Español - España
    4. Español - Méjico
    5. Français
    6. Italiano
    7. Português
    8. Český
    9. Dansk
    10. Nederlands
    11. Magyar
    12. Polski
    13. Svenska
    14. Русский
    15. Türkçe
    16. 中文
    17. Suomi
    18. Norsk
    19. الإنجليزية
    20. български
    21. Hrvatski
    22. Ελληνικά
    23. Română
    24. Slovenský
    25. Slovenščina
    26. 한국어
    27. 日本語
Search
  • μηχανήματα Main Menu
    • Κάθετες φρέζες Haas Κάθετες φρέζες
      Κάθετες φρέζες
      Κάθετες φρέζες View All
      • Κάθετες φρέζες
      • Σειρά VF
      • mηχανεσ γενικησ χρησησ
      • Σειρά VR
      • VMC αλλαγής παλετών
      • Μίνι φρέζες
      • Μηχανήματα κατασκευής καλουπιών
      • Σειρά διάτρησης/σπειροτόμησης/φρεζαρίσματος
      • Φρέζες Toolroom
      • Συμπαγείς φρέζες
      • Σειρά γερανογεφυρών
      • Πολύ μεγάλα VMC
      • Επιτραπέζια φρέζα
      • Αυτόματος φορτωτής τεμαχίων φρέζας
      • Συμπαγής αυτόματος φορτωτής τεμαχίων
    • Product Image Λύσεις πολλαπλών αξόνων
      Λύσεις πολλαπλών αξόνων
      Λύσεις πολλαπλών αξόνων View All
      • Λύσεις πολλαπλών αξόνων
      • Τόρνοι άξονα Υ
      • Φρέζες 5 αξόνων
    • Τόρνοι Haas Τόρνοι
      Τόρνοι
      Τόρνοι View All
      • Τόρνοι
      • Σειρά ST
      • Διπλή άτρακτος
      • Τόρνος Toolroom
      • Τόρνος τύπου Chucker
      • Τροφοδότης μπάρας Haas V2
      • Αυτόματος φορτωτής τεμαχίων τόρνου
    • Οριζόντιες φρέζες Haas Οριζόντιες φρέζες
      Οριζόντιες φρέζες
      Οριζόντιες φρέζες View All
      • Οριζόντιες φρέζες
      • Κώνος 50
      • Κώνος 40
    • Περιστροφικά συστήματα και διαιρέτες Haas Περιστροφικά συστήματα και διαιρέτες
      Περιστροφικά συστήματα και διαιρέτες
      Περιστροφικά συστήματα και διαιρέτες View All
      • Περιστροφικά συστήματα και διαιρέτες
      • Περιστροφικά τραπέζια
      • Διαιρέτες
      • Περιστροφικά συστήματα 5 αξόνων
      • Πολύ μεγάλα περιστροφικά συστήματα
    • Product Image Συστήματα Αυτοματισμού
      Συστήματα Αυτοματισμού
      Συστήματα Αυτοματισμού View All
      • Συστήματα Αυτοματισμού
      • Πακέτα Ρομπότ
      • Αυτόματος φορτωτής τεμαχίων
      • Συστήματα συλλογής παλετών
      • Τροφοδότης μπάρας Haas
      • Models
    • ΓΡΗΓΟΡΟΙ ΣΥΝΔΕΣΜΟΙ Ειδική σειρά  Ειδική σειρά 
      ΘΕΣΕΙΣ ΕΡΓΑΣΙΑΣ HAAS ΘΕΣΕΙΣ ΕΡΓΑΣΙΑΣ HAAS Επέλεξε εξοπλισμό και πάρε τιμή Επέλεξε εξοπλισμό και πάρε τιμή ΤΙΜΟΚΑΤΑΛΟΓΟΣ ΤΙΜΟΚΑΤΑΛΟΓΟΣ ΤΕΛΕΥΤΑΙΕΣ ΕΞΕΛΙΞΕΙΣ ΤΕΛΕΥΤΑΙΕΣ ΕΞΕΛΙΞΕΙΣ ΤΟ ΠΡΩΤΟ ΣΑΣ CNC ΤΟ ΠΡΩΤΟ ΣΑΣ CNC HAAS SIX PACK HAAS SIX PACK
      ΕΡΓΑΛΕΙΑ ΜΗΧΑΝΟΥΡΓΕΙΟΥ
      • Επέλεξε εξοπλισμό και πάρε τιμή ένα νέο Haas
      • Τιμοκατάλογος
      • Διαθέσιμο απόθεμα
      • Χρηματοδότηση CNCA
      ΘΕΛΕΤΕ ΝΑ ΜΙΛΗΣΕΤΕ ΜΕ ΚΑΠΟΙΟΝ;

      Ένα Εργοστασιακό Παράρτημα Haas (HFO) είναι διαθέσιμο να απαντήσει στις ερωτήσεις σας και να παράσχει πληροφορίες για τις καλύτερες επιλογές σας.

      CONTACT YOUR DISTRIBUTOR >
  • Επιλογές Main Menu
    • Product Image Άτρακτοι
      Άτρακτοι
      Άτρακτοι View All
      • Άτρακτοι
    • Product Image Μηχανισμοί αλλαγής εργαλείων
      Μηχανισμοί αλλαγής εργαλείων
      Μηχανισμοί αλλαγής εργαλείων View All
      • Μηχανισμοί αλλαγής εργαλείων
    • Product Image 4ος- | 5ος άξονας
      4ος- | 5ος άξονας
      4ος- | 5ος άξονας View All
      • 4ος- | 5ος άξονας
    • Product Image Εργαλειοφορείς και περιστρεφόμενα εργαλεία
      Εργαλειοφορείς και περιστρεφόμενα εργαλεία
      Εργαλειοφορείς και περιστρεφόμενα εργαλεία View All
      • Εργαλειοφορείς και περιστρεφόμενα εργαλεία
    • Product Image Λήψη μετρήσεων
      Λήψη μετρήσεων
      Λήψη μετρήσεων View All
      • Λήψη μετρήσεων
    • Διαχείριση ρινισμάτων και ψυκτικού υγρού Haas Διαχείριση ρινισμάτων και ψυκτικού υγρού
      Διαχείριση ρινισμάτων και ψυκτικού υγρού
      Διαχείριση ρινισμάτων και ψυκτικού υγρού View All
      • Διαχείριση ρινισμάτων και ψυκτικού υγρού
    • Ο πίνακας ελέγχου Haas Ο πίνακας ελέγχου Haas
      Ο πίνακας ελέγχου Haas
      Ο πίνακας ελέγχου Haas View All
      • Ο πίνακας ελέγχου Haas
    • Product Image Επιλογές προϊόντος
      Επιλογές προϊόντος
      Επιλογές προϊόντος View All
      • Επιλογές προϊόντος
    • Product Image Εργαλεία και Στερέωση σε ιδιοσυσκευή
      Εργαλεία και Στερέωση σε ιδιοσυσκευή
      Εργαλεία και Στερέωση σε ιδιοσυσκευή View All
      • Εργαλεία και Στερέωση σε ιδιοσυσκευή
    • Product Image Διάταξη σύσφιξης κατεργαζόμενου τεμαχίου
      Διάταξη σύσφιξης κατεργαζόμενου τεμαχίου
      Διάταξη σύσφιξης κατεργαζόμενου τεμαχίου View All
      • Διάταξη σύσφιξης κατεργαζόμενου τεμαχίου
    • Product Image Λύσεις 5 αξόνων
      Λύσεις 5 αξόνων
      Λύσεις 5 αξόνων View All
      • Λύσεις 5 αξόνων
      • 5 Easy Steps to 5-Axis
    • Product Image Αυτοματισμός
      Αυτοματισμός
      Αυτοματισμός View All
      • Αυτοματισμός
    • ΓΡΗΓΟΡΟΙ ΣΥΝΔΕΣΜΟΙ Ειδική σειρά  Ειδική σειρά 
      ΘΕΣΕΙΣ ΕΡΓΑΣΙΑΣ HAAS ΘΕΣΕΙΣ ΕΡΓΑΣΙΑΣ HAAS Επέλεξε εξοπλισμό και πάρε τιμή Επέλεξε εξοπλισμό και πάρε τιμή ΤΙΜΟΚΑΤΑΛΟΓΟΣ ΤΙΜΟΚΑΤΑΛΟΓΟΣ ΤΕΛΕΥΤΑΙΕΣ ΕΞΕΛΙΞΕΙΣ ΤΕΛΕΥΤΑΙΕΣ ΕΞΕΛΙΞΕΙΣ ΤΟ ΠΡΩΤΟ ΣΑΣ CNC ΤΟ ΠΡΩΤΟ ΣΑΣ CNC HAAS SIX PACK HAAS SIX PACK
      ΕΡΓΑΛΕΙΑ ΜΗΧΑΝΟΥΡΓΕΙΟΥ
      • Επέλεξε εξοπλισμό και πάρε τιμή ένα νέο Haas
      • Τιμοκατάλογος
      • Διαθέσιμο απόθεμα
      • Χρηματοδότηση CNCA
      ΘΕΛΕΤΕ ΝΑ ΜΙΛΗΣΕΤΕ ΜΕ ΚΑΠΟΙΟΝ;

      Ένα Εργοστασιακό Παράρτημα Haas (HFO) είναι διαθέσιμο να απαντήσει στις ερωτήσεις σας και να παράσχει πληροφορίες για τις καλύτερες επιλογές σας.

      CONTACT YOUR DISTRIBUTOR >
  • Why Haas Main Menu
      Ανακαλύψτε τη διαφορετικότητα της Haas
    • Γιατί Haas
    • MyHaas
    • Εκπαιδευτική Κοινότητα
    • Industry 4.0
    • Πιστοποίηση ISO
    • Μαρτυρίες πελατών
  • Service Main Menu
      Καλωσορίσατε στο σέρβις της Haas
      ΑΡΧΙΚΗ ΣΕΛΙΔΑ ΕΞΥΠΗΡΕΤΗΣΗΣ Σχέδια διάταξης Τρόποι εκτέλεσης Οδηγοί αντιμετώπισης προβλημάτων Προληπτική συντήρηση Εξαρτήματα Haas Haas Tooling Βίντεο
  • Βίντεο Main Menu
  • Main Menu
    • HFO Greece
      HFO Greece
      HFO Greece View All
      • HFO Greece
      • Σχετικά με
      • Υπηρεσία
      • Εκπαίδευση
      • Χρηματοδότηση
      • Απόθεμα εκθεσιακού χώρου
      • Επικοινωνήστε μαζί μας
    • ΓΡΗΓΟΡΟΙ ΣΥΝΔΕΣΜΟΙ Ειδική σειρά  Ειδική σειρά 
      ΘΕΣΕΙΣ ΕΡΓΑΣΙΑΣ HAAS ΘΕΣΕΙΣ ΕΡΓΑΣΙΑΣ HAAS Επέλεξε εξοπλισμό και πάρε τιμή Επέλεξε εξοπλισμό και πάρε τιμή ΤΙΜΟΚΑΤΑΛΟΓΟΣ ΤΙΜΟΚΑΤΑΛΟΓΟΣ ΤΕΛΕΥΤΑΙΕΣ ΕΞΕΛΙΞΕΙΣ ΤΕΛΕΥΤΑΙΕΣ ΕΞΕΛΙΞΕΙΣ ΤΟ ΠΡΩΤΟ ΣΑΣ CNC ΤΟ ΠΡΩΤΟ ΣΑΣ CNC HAAS SIX PACK HAAS SIX PACK
      ΕΡΓΑΛΕΙΑ ΜΗΧΑΝΟΥΡΓΕΙΟΥ
      • Επέλεξε εξοπλισμό και πάρε τιμή ένα νέο Haas
      • Τιμοκατάλογος
      • Διαθέσιμο απόθεμα
      • Χρηματοδότηση CNCA
      ΘΕΛΕΤΕ ΝΑ ΜΙΛΗΣΕΤΕ ΜΕ ΚΑΠΟΙΟΝ;

      Ένα Εργοστασιακό Παράρτημα Haas (HFO) είναι διαθέσιμο να απαντήσει στις ερωτήσεις σας και να παράσχει πληροφορίες για τις καλύτερες επιλογές σας.

      CONTACT YOUR DISTRIBUTOR >
  • Επικοινωνία

×

Αναζήτηση στα αποτελέσματα

Web Pages

Images

    • <
    • 1
    • >
MyHaas Καλωσορίσατε
!
Haas Tooling Ιστορικό παραγγελιών επισκέπτη MyHaas/HaasConnect Σύνδεση Εγγραφή Haas Tooling Ο λογαριασμός μου Order History Return History MyHaas/HaasConnect Αποσύνδεση Καλωσορίσατε Τα μηχανήματά μου Τελευταία δραστηριότητα Οι προσφορές τιμής μου Ο λογαριασμός μου Οι χρήστες μου Αποσύνδεση
Βρείτε έναν αντιπρόσωπο
  1. Επιλέξτε γλώσσα
    1. English
    2. Deutsch
    3. Español - España
    4. Español - Méjico
    5. Français
    6. Italiano
    7. Português
    8. Český
    9. Dansk
    10. Nederlands
    11. Magyar
    12. Polski
    13. Svenska
    14. Русский
    15. Türkçe
    16. 中文
    17. Suomi
    18. Norsk
    19. الإنجليزية
    20. български
    21. Hrvatski
    22. Ελληνικά
    23. Română
    24. Slovenský
    25. Slovenščina
    26. 한국어
    27. 日本語
Search
×

Αναζήτηση στα αποτελέσματα

Web Pages

Images

    • <
    • 1
    • >

UMC-750/1000 Pallet Pool - Installation

Αρχική σελίδα σέρβις Τρόποι εκτέλεσης UMC-750/1000 Pallet Pool - Installation

UMC-750/1000 Pallet Pool - Installation

- Μετάβαση στην ενότητα - Back to Top

3.2 UMC PP - 8/10 Station - Version 2

Recently Updated Last updated: 10/28/2022

UMC PP - 8/10 Station Version 2 - Installation


Pallet Pool Installation Video

Introduction

The following procedure will show you how to install an 8/10 station Pallet Pool on the following machines:

  • UMC-500/SS
  • UMC-750/SS
  • UMC-1000/SS

The Next Generation software on the machine must be version 100.20.000.1110 or higher.

The Pallet Pool option is currently not field installable.

Important: To ensure that the Pallet Pool does not become mis-aligned, it is recommended that the machine and Pallet Pool be anchored. Refer to the following link: Anchoring Instructions.

The Pallet Pool option has a room for a total of 9 pallets that can be installed on a UMC-500/750/1000 with the Pallet Pool option.

The Pallet Pool has 2 servo axes. The PR axis rotates the Pallet Pool ram and the PS axis extends and retracts the Pallet Pool ram to load/unload the pallets.

The UMC-500/750/1000 must be level before the Pallet Pool can be installed. Refer to the installation procedures linked below:

  • UMC-500 Installation
  • UMC-750 Installation
  • UMC-1000 Installation

Push [POWER OFF].

Set the main circuit breaker to the OFF position.

Lock the main circuit breaker. Use an approved lock with an approved safety tag.

Caution: When you handle a PCB, you must wear an Electrostatic Discharge (ESD) strap.

To level the machine without the Pallet Pool connected to the machine, do the following: 

Make sure that there is a shorting block [1] installed on the top two pins of the P12 connector on the I/O PCB 

Make sure there is a jumper (P/N 33-0527) [2] connected to I/O PCB at P14.
 Note: These jumpers are needed to operate the machine without the Pallet Pool.

Disable the pallet pool, change setting 382 Disable Pallet Changer to Pallet Pool.


Note: The above step will disabled the Pallet Pool to allow you to zero return the machine so it can be leveled.

Leveling Screws Hardware

Note: The washers [1] and nuts [2] are installed during shipping and should be saved for installation and not be discarded.

Note: The washer orientation [3] is important.  The conical part of the washer should be against the casting,  see illustration.

Mating the Pallet Pool

   

1

Remove the loading station door blocking bolt [1].

Make sure to raise all of the pallet shelf supporting screws [2] before placing the pallet pool on the floor. 

2

Remove 25-14314 cross bracing from the pallet pool

3

Install the drip tray [1] on the bottom of the auto window, this component should slide right on the window. 

4

Remove the bolts [1] to remove the shipping brackets. There are two brackets, the first [2] that hold the forks to the loading station, and the bottom [3] that just holds the loading station. 

5

Install the Pallet Pool alignment blocks onto the host machine's base.

Note: The alignment block with the radius [2] must be installed towards the back of the UMC and the alignment block with the flat side [1] must be installed towards the front of the machine. Use the three SHCS 3/8-16 X 2 and the one SHCS 3/8-16 X 1 3/8 [4].

Install the alignment bars [3] onto the pallet pool base.

 NOTE: Use the CABCOOL as a height reference in relation to the pallet pool enclosure opening.

Move the pallet pool assembly so the alignment arms are 3 - 6” (76 - 152 mm) away from the alignment blocks. 

Install the leveling pads under the pallet pool and lower the pallet pool. 

6

Use a pallet jack or forklift to move the pallet pool close to the machine.

A decal has been placed on the rear of the machine to indicate where the pallet forks should lift the machine from.

NOTE: Have the pallet jack pick up the pallet pool from the opposite side of where the slide window would be.

7

Install the turnbuckles [3] with the provided hardware (SHCS, washer, and bushings [1]) onto the alignment arms [2] and the base casting [4].

NOTE: The side of the turnbuckle with the two bushings should be installed on the side of the pallet pool.

Evenly tighten the turnbuckles until the alignment arms are almost tight against the alignment bars, STOP once the alignment bars areapproximately 1-2" away from the alignment blocks.

Adjust the height of the pallet pool so that the height of the alignment bars are to the center of the blocks before tightening the turnbuckles flush to the alignment blocks. Raise or lower the pallet pool leveling screws evenly when doing so.

Continue to evenly tighten the turnbuckles until the alignment arms are tight against the alignment blocks.

Once the alignment bars and vlocks are evenly flush to each other loosen up the turn buckles.

8

Turn [OFF] the main circuit breaker and wait until the Vector Drive High-Voltage light turns off.

 Note: The PR (Pallet Rotate) and PS (Pallet Slide) amps are already installed at the factory.

Knock out the pre-cut access panel [1].

Route the pallet pool cables [2] into the control cabinet as shown in the illustration.

Connect the PR motor encoder cable to Maincon PCB channel 15
Connect the PS motor encoder cable to Maincon PCB channel 16.

Connect the PR motor power cable to the amplifier labeled PR. Install the ferrite filter bead on the motor power cable.

Connect the PS motor power cable to the amplifier labeled PS. Install the ferrite filter bead on the motor power cable.

9

Updated

Connect the air gun hose [1] to the air line under the pallet pool [2]. 

Route the air hose from the pallet pool to line coming from the the lube cabinet [3].

Connect the air line from the pallet pool to the to the T-fitting [4] connecting the machine air gun line to the lube cabinet.

Follow the line from the lube cabinet [5] to help locate the T-fitting.

10

Updated

Connect the hydrualic lines to the bulkhead. The pallet clamp [1] is marked with a green zip tie and pallet unclamp [2] is marked with a red zip tie. The hydraulic lines should run through the conduit neatly.

NOTE: The bulkhead uses quick disconnects  for the hydraulic hoses. The clamp side has the male side quick disconnect [3] and the unclamp has the female side [4], this is to avoid switching the hoses.

Route the HPU oil level sensor cable 32-0423 from the HPU to the connector bracket [5].

11

Connect HPU UP/ DWN SOL [1] to P38.

Connect HPU PUMP PWR [2] to P31.

Connect HPU THRML PROBE [3] to P46.

Connect HPU PALLET CLMP SOL  [4] to P35.

Connect HPU PRESSURE SNSR [5] to P48.

Remove the jumper connection from the P14 [6] connector on the I/O PCB.

Connect PP STATUS SWITCHES [7] to P14

Remove the shorting block from the P12 [8] connector on the I/O PCB

Connect PALLET CHNGR STATION [9] to P12

Connect PALLET ALRAM [10]  to P50.

Make sure all the Pallet Pool status bracket connectors are plugged into the correct location.

 NOTE: Store the Pallet Pool jumpers in a safe location, these will be used by the service personnel to move or service the machine.

12

Route the HPU PUMP PWR cable  to P1 on the TMD card located on the I/O PCB hinged door. 

The rest of the components in this image are already connected but this diagram can be used as reference. 

13

Set the main circuit breaker to the ON position.

Push [POWER ON].

Zero Return all the Axis'

Do the following to enable the pallet pool option..  

Important:  You will need to do this step if you perform a option 5 clean install option on a UMC with a pallet pool.

Set setting 382 Disable Pallet Changer to None.

Find the Haas Pallet Pool Parameters decal on the E-Stop on the Pallet Pool machine.  Write down the values.

Use the USB Service key to go into Service Mode.

Press [DIAGNOSTIC] Go to the PARAMETERS> Factory setting tab.

Set the following factory settings values:

  1. 2128 [:] Pallet Pool Type = HPU Lift
  2. 40.011 (HPU 1 Type ) = On Demand
  3. 15.019 [:] PR-Axis Invisible = False
  4. 16.019 [:] PS-Axis Invisible = False
  5. 15.004 [:] PR-Axis Disable = False
  6. 16.004 [16:3] PS-Axis Disabled = False
  7. Turn TMD card on
Set the Grid and TC offsets for PR and PS axis
 
  1. 15.078 PR-Axis Tool Change Offset = Use the decal value.
  2. 15.140 PR-Axis Grid Offset = Use the decal value.
  3. 16.078 PS-Axis Tool Change Offset = Use the decal value.
  4. 16.140 PS-Axis Grid Offset = Use the decal value.
  5. Zero Return after the grid offset is adjusted

Base Level Pallet Pool

1

Verify all outer supports legs are NOT touching the floor.

Make sure the pallet pool sit on 3 points, the leveling foot that is not touching the puck is the one closest to the machine control cabinet [1].

2

Move the ram to its home position if it is not already, place the bubble level on ram and rough level with respect to X & Y. 

NOTE: Rough level by adjusting the 3 leveling feet without adjusting the 4th in the air.

Assigning Missing Pallets on Scheduler

1

It is a possible to enter a condition where the shelves in the pallet scheduling page are not assigned [1]. This will not allow the PR and PS to zero return or recover the machine. 

This section will explain how to assign the missing shelves, if your machine is not in this condition please skip to the next section. 

First, press [CURRENT COMMANDS] and navigate to the Pallet Schedule Table tab.

2

Press [EMERGENCY STOP] [1] and highlight the shelf tab on pallet number one.

With [EMERGENCY STOP] pressed, type the letter A and press [ENTER]. This will assign shelf A to pallet number 1 [2].

3

Repeat the previous step for the remaining pallet numbers in alphabetical number [1].

NOTE: The shelves can be re-assigned at any point  however the user chooses by repeating the same process (e.g. pallet number 3 can be assigned shelf B).

 

Align Pallet Drop Off Station

1

Insert the Service Key USB and put the machine in Service Mode.

Make sure there are no obstructions inside the machine or inside the pallet pool area. Pull out all the [E-STOPS] and [RESET] the alarms.

Press [ZERO RETURN] and then press [ALL]. The machine will zero return all the axes.

Once all the axis are zero returned press [RECOVER]. A pop up box will appear, select [2] for Pallet Changer Recovery.

2

The Pallet Changer Recovery screen shows the Pallet Pool Status. Make sure the Pallet Lifter is Down [1]. If not press [ALTER] to bring the Pallet Lifter down.

Press [J] and then the [DELETE] button. This will rotate the pallet lifter towards station J.

Press [F1] to open the auto window [3].

 

3

While still in the pallet recovery page press [J] then [DELETE] to rotate pallet pool to J position.

Open the window by pressing [F1] then press [+Z] to select Pallet slide Axis manually slide the RAM in the machine to the pickup location.

NOTE: Jog the slide axis slownly and make sure the bottom of the forks clear the receiver casting. Raise the pallet pool evenly if they do not.

With the Pallet Pool in the down position, use the Gap Gauge [1] 25-14354 to set the gap by adjusting the height of the Pallet Pool. Evenly raise or lower the pallet pool leveling screws in accordance to the gap gauge.

NOTE: The pallet pool should still be only on 3 points while adjusting the gap.

 

4

Adjust the pallet pool slider by jogging the PS or PR axis so the forks align correctly underneath the pallet.

The RAM should still be in its slide position, adjust the PR position by pressing [-Z] to select the Pallet Rotate Axis  on the pallet recovery page.  

Press [F2] to unclamp the pallet and press [ALTER] to lift and lower the pallet to make sure the pallet falls onto the pins smoothly. Continuouly make adjustments to the PR and PS axis to make sure the pins are aligned to the holes.

 WARNING: The air blast on the receiver makes a loud noise ear plugs are recommended.

Press [Recovery] to get out of pallet recovery and go to Factory Settings 2139 [:] Shelf J Slide Offset and 2149 [:] Shelf J Rotary Offset, and make sure the values match the PS and PR axis position, if they do not update the values.

NOTE: You should be able to align the pallet pool using factory settings 2136 and 2146 only, if it becomes difficult to do so with only these two settings adjust Parameter 7.310 this is the position that the C-axis will rotate to during a pallet change operation.

Manually remove the pallet from the machine. 

Finally, drop the fourth leveling screw onto the puck.

 

5

Re-enter the pallet recovery page and make sure the pallet is unclamped before pressing [INSERT] to return the RAM to the pallet pool area.

Press [A] then [DELETE] to rotate the RAM to its home position.

Press [A] and [UNDO] to slide the RAM to its home position.

Verify that the level is still acceptable in the X & Y direction [1].

Once verified, zero return the PR and PS axis.

Align Pallet Loading Station

1

Load a pallet onto the loading station, and with the RAM in the loading station use the gap gauge 25-14354 to set the gap between the pins on the RAM forks and the pallet. 

Adjust the two loading station leveling feet until the gap is set. Raise and lower the pallet to ensure it does so smoothly. 

Setting Up Pallet Stations

1

Lower all outer leveling feet [1] to the ground by hand then rotate each leveling foot by another 1/2 turn [2]. 

2

Please refer to the PALLET POOL OPERATORS MANUAL for how to load the pallets onto the machine using the Pallet Scheduling Table.

3

Place the provided tote under the Pallet Pool coolant discharge tray to catch the coolant and chips that drains from the pallets.

Empty the tote as needed. 

Test the pick up / drop off operation on the remaining stations by using the pallet pool recovery functions.  

Install the anchors.

Install the Pallet Pool guard panels.

ΕΥΡΕΣΗ ΔΙΑΝΟΜΕΑ
Ανατροφοδότηση
Haas Logo

美元价格不包括关税、报关费用、保险费、增值税及运费。
USD prices DO NOT include customs duty, customs fees, insurance, VAT, or freight.

人民币价格包含关税、报关费用、货运保险和增值税, 但不包括运费。
CNY prices include customs duty, customs fees, insurance, and VAT. DOES NOT include freight.

Τιμή με παράδοση από τη Haas

Αυτή η τιμή περιλαμβάνει το κόστος αποστολής, τους δασμούς εξαγωγής και εισαγωγής, την ασφάλεια και οποιεσδήποτε άλλες δαπάνες πραγματοποιήθηκαν κατά την αποστολή σε τοποθεσία εντός Γαλλίας, που συμφωνήθηκε μαζί σας ως αγοραστή. Καμία άλλη υποχρεωτική δαπάνη δεν μπορεί να προστεθεί στην παράδοση ενός προϊόντος CNC της Haas.

ΜΕΙΝΕΤΕ ΕΝΗΜΕΡΩΜΕΝΟΙ ΓΙΑ ΤΙΣ ΤΕΛΕΥΤΑΙΕΣ ΣΥΜΒΟΥΛΕΣ ΚΑΙ ΤΗΝ ΤΕΧΝΟΛΟΓΙΑ HAAS...

Εγγραφείτε τώρα!   

HAAS TOOLING ACCEPTS THE FOLLOWING:

  • Service και Υποστήριξη
  • Ιδιοκτήτες
  • Αίτημα Service
  • Εγχειρίδια χειριστή
  • Εξαρτήματα Haas
  • Αίτημα επισκευής περιστροφικού συστήματος
  • Οδηγίες προεγκατάστασης
  • Εργαλεία μηχανουργείου
  • Επέλεξε εξοπλισμό και πάρε τιμή (δημιουργήστε και βάλτε τιμή) ένα νέο Haas
  • Διαθέσιμο απόθεμα
  • Τιμοκατάλογος Haas
  • Χρηματοδότηση CNCA
  • Σχετικά με τη Haas
  • Θέσεις εργασίας
  • Πιστοποιήσεις και ασφάλεια
  • Επικοινωνία
  • Ιστορικό
  • Όροι και Προϋποθέσεις
  • Όροι και Προϋποθέσεις Περιστρεφόμενων Haas Tooling
  • Απόρρητο
  • Εγγύηση
  • Κοινότητα Haas
  • Πρόγραμμα πιστοποίησης CNC της Haas
  • Μηχανοκίνητος αθλητισμός Haas
  • Gene Haas Foundation
  • Κοινότητα Τεχνικής Εκπαίδευσης της Haas
  • Εκδηλώσεις
  • Μπείτε στη συζήτηση
  • Facebook
  • Twitter
  • Flickr
  • YouTube
  • LinkedIn
  • Instagram
  • TikTok
© 2023 Haas Automation, Inc – Εργαλειομηχανές CNC

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.


2800 Sturgis Rd., Oxnard, CA 93030 / Toll Free: 800-331-6746
Phone: 805-278-1800 / Fax: 805-278-2255

Ειδοποίηση για τα Cookies

Χρησιμοποιούμε cookies για να βελτιώνουμε την εμπειρία χρήστη. Η Δήλωση Cookies περιγράφει ποια cookies που χρησιμοποιούμε, γιατί τα χρησιμοποιούμε και πώς μπορείτε να βρείτε περισσότερες πληροφορίες σχετικά με αυτά. Επιβεβαιώσετε τη συγκατάθεσή σας για τη χρήση των cookies ανάλυσης. Αν δεν επιθυμείτε να δώσετε τη συγκατάθεσή σας, μπορείτε να συνεχίσετε να χρησιμοποιείτε τον ιστότοπό μας με μειωμένη εμπειρία χρήστη.

Διαχείριση Ρυθμίσεων

Ειδοποίηση για τα Cookies

Χρησιμοποιούμε cookies για να βελτιώνουμε την εμπειρία χρήστη. Η Δήλωση Cookies περιγράφει ποια cookies που χρησιμοποιούμε, γιατί τα χρησιμοποιούμε και πώς μπορείτε να βρείτε περισσότερες πληροφορίες σχετικά με αυτά. Επιβεβαιώσετε τη συγκατάθεσή σας για τη χρήση των cookies ανάλυσης. Αν δεν επιθυμείτε να δώσετε τη συγκατάθεσή σας, μπορείτε να συνεχίσετε να χρησιμοποιείτε τον ιστότοπό μας με μειωμένη εμπειρία χρήστη.

Functional Cookies

Analytics Cookies