MyHaas Dobro došli,
!
Haas Tooling Povijest naloga posjetilaca MyHaas/HaasConnect Prijava Registrirajte se Haas Tooling Moj račun Order History Return History MyHaas/HaasConnect Odjava Dobro došli, Moji strojevi Zadnja aktivnost Moje ponude Moj račun Moji korisnici Odjava
0
Pronađite zastupnika
  1. Odaberite jezik
    1. English
    2. Deutsch
    3. Español - España
    4. Español - México
    5. Français
    6. Italiano
    7. Português
    8. Český
    9. Dansk
    10. Nederlands
    11. Magyar
    12. Polski
    13. Svenska
    14. Türkçe
    15. 中文
    16. Suomi
    17. Norsk
    18. الإنجليزية
    19. български
    20. Hrvatski
    21. Ελληνικά
    22. Română
    23. Slovenský
    24. Slovenščina
    25. 한국어
    26. 日本語
    27. Українська
  • strojevi Main Menu
    • Vertikalne glodalice Haas Vertikalne glodalice
      Vertikalne glodalice
      Vertikalne glodalice View All
      • Vertikalne glodalice
      • VF serija
      • Univerzalni strojevi
      • VR serija
      • VP-5 prizmatski stroj
      • VMC-ovi za izmjenu paleta
      • Male glodalice
      • Strojevi za modeliranje
      • Centri za bušenje velike brzine
      • Serija strojeva za bušenje/narezivanje/glodanje
      • Alatne glodalice
      • Kompaktne glodalice
      • Serije pokretnih postolja
      • SR Usmjernici za ploče
      • Iznimno veliki VMC strojevi
      • Glodalice s dvostrukim stupcem
      • Upravljački simulator
      • Automatski sustav za dodavanje sirovca za glodalicu
      • VMC/UMC automatski sustav za dodavanje sirovca s bočnim punjenjem
      • Kompaktni APL
    • Product Image Višeosna rješenja
      Višeosna rješenja
      Višeosna rješenja View All
      • Višeosna rješenja
      • Y-osne tokarilice
      • 5-osne glodalice
    • Haas tokarilice Tokarilica
      Tokarilica
      Tokarilica View All
      • Tokarilica
      • ST serije
      • Dva glavnog vretena
      • Serija Box Way
      • Alatne tokarilice
      • Konjić tokarilice
      • Haas dodavač šipke V2
      • Automatski sustav za dodavanje sirovca za tokarilicu
    • Haas horizontalne glodalice Horizontalne glodalice
      Horizontalne glodalice
      Horizontalne glodalice View All
      • Horizontalne glodalice
      • Konus 50
      • Konus 40
    • rotacioni proizvodi i indekseri Haas rotacioni proizvodi i indekseri
      rotacioni proizvodi i indekseri
      rotacioni proizvodi i indekseri View All
      • rotacioni proizvodi i indekseri
      • Okretni stolovi
      • Indekseri
      • 5-osne rotacione jedinice
      • Iznimno velike rotacione jedinice
    • Product Image Sustavi automatizacije
      Sustavi automatizacije
      Sustavi automatizacije View All
      • Sustavi automatizacije
      • Automatizacija glodalice
      • Automatizacija tokarilice
      • Modeli za automatizaciju
    • Haasovi centri za bušenje Desktop strojevi
      Desktop strojevi
      Desktop strojevi View All
      • Desktop strojevi
      • Desktop glodalica
      • Desktop tokarilica
    • Haas oprema za radionice Oprema za radionice
      Oprema za radionice
      Oprema za radionice View All
      • Oprema za radionice
      • Tračna pila
      • Konzolna glodalica
      • Površinska brusilica, 2550
      • Površinska brusilica, 3063
      • Laserski stroj za rezanje
    • BRZE POVEZNICE Posebne serije  Posebne serije 
      EU SERIJE EU SERIJE KONFIGURACIJA I CIJENA | CJENIK KONFIGURACIJA I CIJENA | CJENIK Strojevi na zalihi Strojevi na zalihi ŠTO JE NOVO ŠTO JE NOVO VAŠ PRVI CNC VAŠ PRVI CNC
      ALATI ZA KUPNJU
      • Sastavite i izradite cijenu Haas stroja
      • Cjenik
      • Dostupan inventar
      • CNCA financiranje
      ŽELITE RAZGOVARATI S NEKIM?

      Haas tvornički dućan (outlet) (HFO) može odgovoriti na vaša pitanja i provesti vas kroz najbolje opcije.

      CONTACT YOUR DISTRIBUTOR >
  • Opcije Main Menu
    • Product Image Glavna vretena
      Glavna vretena
      Glavna vretena View All
      • Glavna vretena
    • Product Image Izmjenjivači alata
      Izmjenjivači alata
      Izmjenjivači alata View All
      • Izmjenjivači alata
    • Product Image 4- | 5-osni
      4- | 5-osni
      4- | 5-osni View All
      • 4- | 5-osni
    • Product Image Revolveri i pogonjeni alati
      Revolveri i pogonjeni alati
      Revolveri i pogonjeni alati View All
      • Revolveri i pogonjeni alati
    • Product Image Sondiranje
      Sondiranje
      Sondiranje View All
      • Sondiranje
    • Haas Upravljanje strugotinom i rashladnim sredstvima Upravljanje strugotinom i rashladnim sredstvima
      Upravljanje strugotinom i rashladnim sredstvima
      Upravljanje strugotinom i rashladnim sredstvima View All
      • Upravljanje strugotinom i rashladnim sredstvima
    • Haas upravljačka naprava Haas upravljačka naprava
      Haas upravljačka naprava
      Haas upravljačka naprava View All
      • Haas upravljačka naprava
    • Product Image Opcije proizvoda
      Opcije proizvoda
      Opcije proizvoda View All
      • Opcije proizvoda
    • Product Image Alati i Stezanje i prihvat sirovca
      Alati i Stezanje i prihvat sirovca
      Alati i Stezanje i prihvat sirovca View All
      • Alati i Stezanje i prihvat sirovca
    • Product Image Držač obratka
      Držač obratka
      Držač obratka View All
      • Držač obratka
    • View All
    • Product Image 5-osna rješenja
      5-osna rješenja
      5-osna rješenja View All
      • 5-osna rješenja
      • 5 Easy Steps to 5-Axis
    • Product Image Automatizacija
      Automatizacija
      Automatizacija View All
      • Automatizacija
    • BRZE POVEZNICE Posebne serije  Posebne serije 
      EU SERIJE EU SERIJE KONFIGURACIJA I CIJENA | CJENIK KONFIGURACIJA I CIJENA | CJENIK Strojevi na zalihi Strojevi na zalihi ŠTO JE NOVO ŠTO JE NOVO VAŠ PRVI CNC VAŠ PRVI CNC
      ALATI ZA KUPNJU
      • Sastavite i izradite cijenu Haas stroja
      • Cjenik
      • Dostupan inventar
      • CNCA financiranje
      ŽELITE RAZGOVARATI S NEKIM?

      Haas tvornički dućan (outlet) (HFO) može odgovoriti na vaša pitanja i provesti vas kroz najbolje opcije.

      CONTACT YOUR DISTRIBUTOR >
  • Why Haas Main Menu
      Otkrijte Haas razliku
    • Zašto Haas
    • MyHaas
    • Edukacijska zajednica
    • Industry 4.0
    • Haas certifikat
    • Svjedočenja kupaca
  • Servis Main Menu
      Dobrodošli u Haas Service
      POČETNA STRANICA SERVISA Priručnici za korisnika Upute za izvršenje Upute za rješavanje problema Preventivno održavanje Haas dijelovi Haas Tooling Videozapisi
  • Videozapisi Main Menu
×

Rezultati pretrage

Web Pages

Images

    • <
    • 1
    • >
Use the up and down arrows to select a result. Press enter to go to the selected search result. Touch device users can use touch and swipe gestures.
MyHaas Dobro došli,
!
Haas Tooling Povijest naloga posjetilaca MyHaas/HaasConnect Prijava Registrirajte se Haas Tooling Moj račun Order History Return History MyHaas/HaasConnect Odjava Dobro došli, Moji strojevi Zadnja aktivnost Moje ponude Moj račun Moji korisnici Odjava
0
Pronađite zastupnika
  1. Odaberite jezik
    1. English
    2. Deutsch
    3. Español - España
    4. Español - México
    5. Français
    6. Italiano
    7. Português
    8. Český
    9. Dansk
    10. Nederlands
    11. Magyar
    12. Polski
    13. Svenska
    14. Türkçe
    15. 中文
    16. Suomi
    17. Norsk
    18. الإنجليزية
    19. български
    20. Hrvatski
    21. Ελληνικά
    22. Română
    23. Slovenský
    24. Slovenščina
    25. 한국어
    26. 日本語
    27. Українська
×

Rezultati pretrage

Web Pages

Images

    • <
    • 1
    • >

Coolant Level Float Sensor - Troubleshooting Guide

Početna stranica servisa Plutajući senzor razine rashladnog sredstva - Vodič za otklanjanje poteškoća

Plutajući senzor razine rashladnog sredstva - Vodič za otklanjanje poteškoća

- Preskoči na uzrok - Back to Top

16.2 Coolant Level Float Sensor - Troubleshooting Guide

Recently Updated Last updated: 04/25/2025

Coolant Float Sensor - Troubleshooting Guide


Revision A - 04/2025

Coolant Level Float Sensor Inspection Report

Download and fill out the Coolant Float Sensor Inspection Report Checklist below before replacing any parts.

Coolant Float Sensor Inspection Report

Introduction

The image shows the following components of the Coolant Float Sensor:

  1. Float [1]
  2. Potentiometer [2]
  3. Bracket [3]
  4. Power Cord [4]
  5. Potentiometer Cover (not shown for clarity)

Symptom Table

Symptom Possible Cause Corrective Action
The coolant level sensor displays an incorrect coolant level. The coolant float is installed incorrectly.  See Check Float Installation section below.
The float is blocked and cannot move.  Clear all chips from float and coolant tank. 
The factory settings 603 and 604 have the incorrect values.  Refer to Coolant Level Float Sensor - Installation for the correct parameter values.
The cable is damaged or unplugged.  Make sure that the cable is securely connected and is not damaged. 
The sensor is damaged. Check all of the wires and clear chips blocking the float. Inspect for any leaks. If issue persists, follow the Malfunctioning Sensor section below. 
Coolant level sensor displays 0% with no change when level sensor is moved up/down.  The coolant float is installed incorrectly.   See Check Float Installation section below.
The sensor is damaged or the float cannot move.  Check all of the wires and clear chips blocking the float. Inspect for any leaks. If issue persists, follow the Malfunctioning Sensor section below. 
The I/O PCB isn't configured properly with the coolant level sensor.  Display analog input 13 while manually moving the coolant level float up/down. The input value should change from ~2500 to ~3150. If the input value remains the same, make sure that I/O configuration is correct. A-Input 13 should be mapped to P43.1. Refer to I/O Mapping section below. 

Low coolant alerts appearing and disappearing frequently while machine is idle.

20022 and 20023 notification occurences in Alarm History.

Coolant level is close to 50%.  Fill coolant tank until coolant touches chip filter. Ensure that coolant level is above 70% before starting any operation that requires coolant. Clear any chips and debris from coolant filter, tank and machine. If issue persists, follow the Malfunctioning Sensor section below. 

Low coolant alerts appearing and disappearing frequently while machine is cutting.

20022 and 20023 notification occurences in Alarm History.

Coolant is cycling through the machine during operations.  Fill coolant tank until coolant touches chip filter. Ensure that coolant level is above 70% before starting any operation that requires coolant. Clear any chips and debris from coolant filter, tank, and machine. If issue persists, follow the Malfunctioning Sensor section below. 

Check Float Installation

1

Check the orientation of the coolant tank lid. The cutout containing the coolant float [1] should be on the side of the coolant tank closest to the machine, as shown.

Ensure that the lid is sitting flat on top of the coolant tank. 

2

Check that the dimples on the coolant float are properly seated in the dimples on the coolant tank. Check that the coolant float is sitting flat on top of the lid. 

3

Re-fill coolant tank until coolant level touches the bottom of the chip filter [1]. 

Malfunctioning Sensor

In the first image, you can see the location of the coolant level sensor on the coolant tank.

If your coolant level sensor does not display the correct level on the screen, look in the coolant tank to make sure a chip build-up does not block the float from moving freely. Also, inspect the float for any leaks to make sure no coolant has wept in. 

Corrective Action:

Make sure the coolant level sensor operates correctly:

  • Press [MEMORY]. The upper-right corner of the screen will show the coolant level.
  • Remove the coolant float sensor from the tank and manually move the float to max and min conditions.  The coolant level indicator on the screen should move at a slow pace. It takes approximately (1) minute to move from empty [2] to full [1] on the screen, but it starts to move immediately. Note the percentages that the coolant level indicator reports when the float is at min and max conditions. 
  • If the coolant level sensor does not operate correctly, unplug the coolant level sensor from the machine.

 

Measure the voltage across the black [1] and blue [2] wires on P43 on the I/O board when the float is up and down. The voltage should be approximately 3.8V when the float is up and 2.6V when it is down.

 

Measure the resistance at pins [2] and [4] on M12 connector when the float is up and down. The resistance should be approximately 371 Ohms when the float is up and 286 Ohms when it is down.

NOTE: Do not remove the coating around the wire, rather take the reading at the M12.

 

If another machine is present, test float on different machine. If the coolant level sensor continues to read incorrectly, and you have completed the troubleshooting instructions, replace the sensor.

 IMPORTANT: When returning the sensor, make sure to include an error report.

 IMPORTANT: When returning the sensor, please include the following information:

  • Machine state during malfunction (idle or cutting)
  • A video showing coolant level in the tank and on the pendant screen
  • Error Report
  • Resistance across black and white wires (see above)

I/O Mapping

The coolant level float sensor is controlled by analog input 13. The analog input uses an electronic counter to measure the input voltage signal. This input voltage signal is shown in the value section. For more information, refer to the Analog Sensors - Troubleshooting Guide. 

As the coolant lower in the tank, the less input voltage there should be. As the coolant raises in the tank, the more input voltage there should be. When moving the coolant level float, the voltage value should change from ~2500 to ~3150.

The coolant level float sensor is connected to the I/O board at pin 43 shown in the connector section. Check the end of the M12 cable that is plugged into the I/O board to make sure the voltage across pin 3 and 4. If the 5VDC is not present, then troubleshoot the I/O PCB refer to the I/O PCB - Troubleshooting Guide. 

Electrical Schematic

Recently Viewed Items

You Have No Recently Viewed Items Yet

Povratna veza
Haas Logo

美元价格不包括关税、报关费用、保险费、增值税及运费。
USD prices DO NOT include customs duty, customs fees, insurance, VAT, or freight.

人民币价格包含关税、报关费用、货运保险和增值税, 但不包括运费。
CNY prices include customs duty, customs fees, insurance, and VAT. DOES NOT include freight.

Haas cijena s dostavom

Ova cijena uključuje troškove dostave, izvozne i uvozne carine, osiguranje i sve druge troškove dostave na lokaciju u Francuskoj dogovorenu s vama kao kupcem. Nikakvi drugi obvezni troškovi ne mogu se dodati u cijenu dostave Haas CNC proizvoda.

OSTANITE U TIJEKU S NAJNOVIJIM HAAS SAVJETIMA I TEHNOLOGIJAMA…

Prijavite se sad!   

HAAS TOOLING ACCEPTS THE FOLLOWING:

  • Servis i podrška
  • Vlasnici
  • Zatražite servis
  • Korisnički priručnik
  • Haas dijelovi
  • Zahtjev za popravak okretnog ili okretno nagibnog aparata
  • Vodič prije ugradnje
  • Alati za kupovinu
  • Cijena izrade novog Haasovog stroja
  • Dostupan inventar
  • Cjenik tvrtke Haas
  • CNCA financiranje
  • O tvrtki Haas
  • Izjava DNSH
  • Zapošljavanje
  • Certifikati i sigurnost
  • Obratite nam se
  • Povijest
  • Uvjeti i odredbe
  • Uvjeti i odredbe za Haas Tooling
  • Privatnost
  • Jamstvo
  • Zajednica Haas
  • Haas CNC program certifikacije
  • Motosportovi Haas
  • Zaklada Gene Haas
  • Tehnička edukacijska zajednica tvrtke Haas
  • Događanja
  • Pridružite se razgovoru
  • Facebook
  • X
  • Flickr
  • YouTube
  • LinkedIn
  • Instagram
  • TikTok
© 2025 Haas Automation, Inc – CNC alatni strojevi

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

2800 Sturgis Rd., Oxnard, CA 93030 / Toll Free: 800-331-6746
Phone: 805-278-1800 / Fax: 805-278-2255