MyHaas Üdvözöljük!
!
Haas Tooling Vendég korábbi megrendelései MyHaas/HaasConnect Bejelentkezés Regisztráció Haas Tooling Saját fiók Order History Return History MyHaas/HaasConnect Kijelentkezés Üdvözöljük! Saját gépek Legutolsó tevékenység Saját árajánlatok Saját fiók Saját felhasználók Kijelentkezés
Keresse meg forgalmazóját
  1. Válasszon nyelvet
    1. English
    2. Deutsch
    3. Español - España
    4. Español - México
    5. Français
    6. Italiano
    7. Português
    8. Český
    9. Dansk
    10. Nederlands
    11. Magyar
    12. Polski
    13. Svenska
    14. Türkçe
    15. 中文
    16. Suomi
    17. Norsk
    18. الإنجليزية
    19. български
    20. Hrvatski
    21. Ελληνικά
    22. Română
    23. Slovenský
    24. Slovenščina
    25. 한국어
    26. 日本語
    27. Українська
  • gépek Main Menu
    • Haas függőleges marók Függőleges marók
      Függőleges marók
      Függőleges marók View All
      • Függőleges marók
      • VF sorozat
      • Univerzális gépek
      • VR-sorozat
      • VP-5 Prismatic
      • Palettacserélős VMC-k
      • Minimaró
      • Formázógépek
      • Nagysebességű fúróközpontok
      • Fúró/menetfúró/maró sorozat
      • Szerszámmarók
      • Kompakt marók
      • Állványzat sorozatok
      • SR lapmarók
      • Extranagy VMC
      • Dupla oszlopos marók
      • Vezérlőszimulátor
      • Automata munkadarab-adagoló marógéphez
      • VMC/UMC oldalsó betöltésű APL
      • Kompakt automata munkadarab adagoló (APL)
    • Product Image Többtengelyes megoldások
      Többtengelyes megoldások
      Többtengelyes megoldások View All
      • Többtengelyes megoldások
      • Y-tengelyű esztergák
      • 5-tengelyes marók
    • Haas esztergák Esztergák
      Esztergák
      Esztergák View All
      • Esztergák
      • ST sorozat
      • Kettős orsó
      • Dobozos sorozat
      • Szerszámesztergák
      • Tokmányos eszterga
      • Haas rúdadagoló V2
      • Automata munkadarab-adagoló esztergához
    • Haas vízszintes marók Vízszintes marók
      Vízszintes marók
      Vízszintes marók View All
      • Vízszintes marók
      • SK-50
      • SK-40
    • Haas forgóasztalok és indexelők Teszt lábjegyzet szöveg
      Teszt lábjegyzet szöveg
      Teszt lábjegyzet szöveg View All
      • Teszt lábjegyzet szöveg
      • Forgóasztalok
      • Indexelők
      • 5-tengelyes forgóasztalok
      • Extra méretű forgóasztalok
    • Product Image Automatizálási rendszerek
      Automatizálási rendszerek
      Automatizálási rendszerek View All
      • Automatizálási rendszerek
      • Maró automatizálása
      • Eszterga automatizálása
      • Automatizálási modellek
    • Haas fúróközpontok Asztali gépek
      Asztali gépek
      Asztali gépek View All
      • Asztali gépek
      • Asztali maró
      • Asztali eszterga
    • Haas műhelyi berendezések Berendezések vásárlása
      Berendezések vásárlása
      Berendezések vásárlása View All
      • Berendezések vásárlása
      • Szalagfűrész
      • Térdmaró
      • Felületcsiszoló, 2550
      • Lézervágó gép
    • GYORSHIVATKOZÁSOK Speciális sorozat  Speciális sorozat 
      EU SOROZAT EU SOROZAT KIÉPÍTÉS ÉS ÁR | ÁRLISTA KIÉPÍTÉS ÉS ÁR | ÁRLISTA Készleten lévő gépek Készleten lévő gépek MIK AZ ÚJDONSÁGOK? MIK AZ ÚJDONSÁGOK? AZ ÖN ELSŐ CNC GÉPE AZ ÖN ELSŐ CNC GÉPE
      SZERSZÁMOK VÁSÁRLÁSA
      • Haas gép kiépítés és árazás
      • Árlista
      • Elérhető készlet
      • CNCA finanszírozás
      SZERETNE BESZÉLNI VALAKIVEL?

      A Haas gyárfiók (HFO) válaszol kérdéseire, és bemutatja a legjobb lehetőségeket.

      CONTACT YOUR DISTRIBUTOR >
  • Opciók Main Menu
    • Product Image Orsók
      Orsók
      Orsók View All
      • Orsók
    • Product Image Szerszámváltók
      Szerszámváltók
      Szerszámváltók View All
      • Szerszámváltók
    • Product Image 4. | 5. tengely
      4. | 5. tengely
      4. | 5. tengely View All
      • 4. | 5. tengely
    • Product Image Revolverek és hajtott szerszámozás
      Revolverek és hajtott szerszámozás
      Revolverek és hajtott szerszámozás View All
      • Revolverek és hajtott szerszámozás
    • Product Image Mérés mérőérintkezővel
      Mérés mérőérintkezővel
      Mérés mérőérintkezővel View All
      • Mérés mérőérintkezővel
    • Haas forgács- és hűtőközeg-kezelés Forgács- és hűtőközeg-kezelés
      Forgács- és hűtőközeg-kezelés
      Forgács- és hűtőközeg-kezelés View All
      • Forgács- és hűtőközeg-kezelés
    • A Haas-vezérlés A Haas-vezérlés
      A Haas-vezérlés
      A Haas-vezérlés View All
      • A Haas-vezérlés
    • Product Image Termékopciók
      Termékopciók
      Termékopciók View All
      • Termékopciók
    • Product Image Szerszámozás és befogás
      Szerszámozás és befogás
      Szerszámozás és befogás View All
      • Szerszámozás és befogás
    • Product Image Munkadarab befogó
      Munkadarab befogó
      Munkadarab befogó View All
      • Munkadarab befogó
    • Product Image 5-tengelyes megoldások
      5-tengelyes megoldások
      5-tengelyes megoldások View All
      • 5-tengelyes megoldások
      • 5 Easy Steps to 5-Axis
    • Product Image Automatizálás
      Automatizálás
      Automatizálás View All
      • Automatizálás
    • GYORSHIVATKOZÁSOK Speciális sorozat  Speciális sorozat 
      EU SOROZAT EU SOROZAT KIÉPÍTÉS ÉS ÁR | ÁRLISTA KIÉPÍTÉS ÉS ÁR | ÁRLISTA Készleten lévő gépek Készleten lévő gépek MIK AZ ÚJDONSÁGOK? MIK AZ ÚJDONSÁGOK? AZ ÖN ELSŐ CNC GÉPE AZ ÖN ELSŐ CNC GÉPE
      SZERSZÁMOK VÁSÁRLÁSA
      • Haas gép kiépítés és árazás
      • Árlista
      • Elérhető készlet
      • CNCA finanszírozás
      SZERETNE BESZÉLNI VALAKIVEL?

      A Haas gyárfiók (HFO) válaszol kérdéseire, és bemutatja a legjobb lehetőségeket.

      CONTACT YOUR DISTRIBUTOR >
  • Why Haas Main Menu
      Fedezze fel, hogy miben különbözik a Haas
    • Miért Haas?
    • MyHaas
    • Oktatóközösség
    • Ipar 4.0
    • Haas tanúsítás
    • Vásárlói élmények
  • Szerviz Main Menu
      A Haas Service üdvözli Önt
      SZERVIZ KEZDŐLAP Kezelői kézikönyvek Eljárási módok Hibaelhárítási útmutató Megelozo karbantartás Haas alkatrészek Haas Tooling Videók
  • Videók Main Menu
×

Keresési eredmények

Web Pages

Images

    • <
    • 1
    • >
MyHaas Üdvözöljük!
!
Haas Tooling Vendég korábbi megrendelései MyHaas/HaasConnect Bejelentkezés Regisztráció Haas Tooling Saját fiók Order History Return History MyHaas/HaasConnect Kijelentkezés Üdvözöljük! Saját gépek Legutolsó tevékenység Saját árajánlatok Saját fiók Saját felhasználók Kijelentkezés
Keresse meg forgalmazóját
  1. Válasszon nyelvet
    1. English
    2. Deutsch
    3. Español - España
    4. Español - México
    5. Français
    6. Italiano
    7. Português
    8. Český
    9. Dansk
    10. Nederlands
    11. Magyar
    12. Polski
    13. Svenska
    14. Türkçe
    15. 中文
    16. Suomi
    17. Norsk
    18. الإنجليزية
    19. български
    20. Hrvatski
    21. Ελληνικά
    22. Română
    23. Slovenský
    24. Slovenščina
    25. 한국어
    26. 日本語
    27. Українська
×

Keresési eredmények

Web Pages

Images

    • <
    • 1
    • >

Analog Sensors - Troubleshooting Guide - NGC

Szerviz kezdőlap Analog Sensors - Troubleshooting Guide - NGC

Analog Sensors - Troubleshooting Guide - NGC

- Ugrás az okhoz - Back to Top
Recently Updated Last updated: 06/13/2025

Analog Sensors - Troubleshooting Guide - NCG


Revision A - 06/2025

Analog Input Troubleshooting Video

The following service video provides information on troubleshooting analog inputs.

Note: This service video is for reference only and does not replace the written procedure. 

A Haas machine, depending on the vintage, has anywhere between one and eight analog sensors in various systems throughout the machine. All of these sensors share a common ground. A problem with one of these sensors could potentially affect the signal from all of them, making troubleshooting difficult. If you are troubleshooting a problem with any of these sensors, their cables or the Maincon/ I/O PCB follow these simple steps:

  1. Look at the gauge page and identify the readings that look unreasonable. For example, if the spindle motor temperature [1] reads 0-degrees Fahrenheit and the shop is at 77-degrees this is not reasonable.
  2. If one of these cables or sensors has a short-circuit. The gauge display will show several readings that are not reasonable.
  3. Unplug each analog sensor one at a time. Look for the other gauge readings to return to something reasonable.

     Note: Some signals may take up to 30 seconds to react.

  4. When you find the sensor that is causing the inaccurate readings you have most likely found the problem. Check the cable for damage. Check the sensor.

     Note: The cable or the sensor are more likely to be the cause of the problem than the Maincon / I/O PCB.

Symptom Table

Symptom Possible Cause Corrective Action
Alarm 120 Low Air Pressure Or Flow The compressed air supplied to the machine is below the minimum pressure or flow required. 

Check for contamination in air pressure sensor. If contamination is found, sensor must be replaced.

Important: Ensure that air supply to the machine is clean and dry to avoid repeat failures. 

Alarm 9916 EXCESSIVE THERMAL COMPENSATION DISTANCE There is electrical noise on the signal or the thermal sensor is faulty. Check the thermal sensor input in diagnostics and see if the signal is fluctuating.  If signal is fluctuating,  inspect the amplifiers and make sure there is a ferrite bead on ALL axis power cables. Check for loose connection or damage to the thermal sensor cable.  If all checks have been done the thermal sensor is faulty.
Alarm 9940 AXIS THERMAL SENSOR FAULT There is electrical noise on the signal or the thermal sensor is faulty. Check the thermal sensor input in diagnostics and see if the signal is fluctuating.  If signal is fluctuating,  inspect the amplifiers and make sure there is a ferrite bead on ALL axis power cables. Check for loose connection or damage to the thermal sensor cable.  If all checks have been done the thermal sensor is faulty.
The cable or sensor is disconnected. Check for loose connection or damage to the thermal sensor cable. 

At Power On:

Alarm 4.9940 AXIS THERMAL SENSOR FAULT

Is generated.

The I/O Main Firmware is outdated. Make sure the I/O Main Firmware is version 4.09 or higher.  Refer to the I/O Firmware Upgrade procedure.

After software update machine generates 

Alarm 4.9916 / 9916 EXCESSIVE THERMAL COMPENSATION DISTANCE

OR

4.9940 / 9940 AXIS THERMAL SENSOR FAULT

Invalid I/O configuration files. Make sure that the thermal sensor is mapped to the correct I/O analog input.
This applies to UMC machines:  Axis thermal sensor cable is plugged into the wrong analog input. Make sure the axis thermal sensor cable is plugged into P45 on the I/O PCB.
There is electrical noise on the signal or the thermal sensor is faulty. Check the thermal sensor input in diagnostics and see if the signal is fluctuating.  If signal is fluctuating,  inspect the amplifiers and make sure there is a ferrite bead on ALL axis power cables. Check for loose connection or damage to the thermal sensor cable.  If all checks have been done the thermal sensor is faulty.
ALARM 9941 CRASH DETECTED (spindle head accelerometer)  The machine detected a crash Verify the program machine movements to make sure the machine does not crash
The Accelerometer unit, cable or spindle head CAN board is damaged
  • Verify analog inputs are not 0 (cable unplugged)
  • I/O board minimum version 4.09 (update to latest if possible)
  • Spindle head CAN board minimum 1.10 (update to latest if possible
  • Make sure to take an error report (SHIFT+F3), error reports will have information about the crash direction and magnitude in the JavaConsoleLog.txt file (refer to Crash Detection Section in the Accelerometer Troubleshooting Guide for further information)
ALARM 966 EXCESSIVE TOOL IMBALANCE (board accelerometer) Excessive tool vibration is generated by on board accelerometer Verify that everything is properly balanced, such as tools and spindles

Reduce sensitivity using Setting 245

  • Setting 245 = Normal: Means that parameter 856 is directly used
  • Setting 245 = Low: Means that parameter 856 is multiplied by 1.5
  • Setting 245 = Off: Alarm 966 will not be thrown. 

NOTE: Setting 245 will not persist when the power is cycled

Please refer to the  Accelerometer Troubleshooting Guide for further information

Spindle motor temperature sensor fluctuating Electrical noise around that area. A ground wire should added from the motor lift bracket to the spindle heat shield. Refer to: HSG-N 08-23-2024.

NGC - Analog Sensor Information

Note: The connector location of these sensors can change,  please check the location on the screen.  Press [DIAGNOSTIC] and go to the I/O tab and search for keyword "ANALOG" and press [F1].

The raw data analog sensors that are connected to the Maincon PCB, can be view under the Mocon tab.

Gauge Name / Analog Sensor
Analog Sensor Location
Analog Sensor Connector Location*
Alarm / Warning

Mills: TSC Pressure

Lathe: HPC Pressure

Mills: On the TSC pump.

Lathe: On the HPC pump.

I/O PCB P39.21

Mills: Alarm 151 LOW THRU-SPINDLE COOLANT

Lathe: Alarm 8151 HPC LOW PRESSURE.

EC-1600: Y-axis temperature sensor. On the Y-axis column. I/O PCB P39.19 N/A
Lathe: X-axis temperature sensor.
On the X-axis ballscrew ballnut.
I/O PCB P2.14 N/A
Coolant Level
On the coolant level float.
I/O PCB P43.1 Low coolant Icon will apper when the coolant level is low.  The Low Coolant Concentrate icon will appear when machine is equipped with the Coolant Refill option.
Coolant Temperature On the coolant filter. I/O PCB P44.1 This temperature is for display purposes only and is shown on the gauge tab if the hardware is installed and enabled.
HPU Low Hydraulic Pressure On the hydraulic power unit. I/O PCB P48.7 Alarm 8134 LOW HYDRAULIC PRESSURE ON START
Note: UMC's that are equipped with Hydraulic Brakes for the B and C-axis can generate this alarm after a software upgrade if the hydraulic analog pressure sensor input is not mapped correctly.  Make sure the IO Configuration file has the correct mapping.
HPU Oil Temperature
On the hydraulic power unit.
I/O PCB P46.1

Alarm 2096 HPU OIL TEMPERATURE TOO HIGH

Spindle Temperature On the spindle head. I/O PCB P39.24 This temperature is for display purposes only and is shown on the gauge tab if the hardware is installed and enabled.
Spindle Motor Temperature
On the spindle motor .
I/O PCB P39.22 Alarm 254 SPINDLE MOTOR OVERHEAT
Analog Air Pressure
On the air-lube cabinet.
I/O PCB P34.5 Alarm 120 LOW AIR PRESSURE
Ambient Temperature On the base casting. I/O PCB P51.1 This temperature is for display purposes only and is shown on the gauge tab if the hardware is installed and enabled.
DC Voltage
Inside the vector drive (the sensor is not serviceable).
Maincon PCB J16 Alarm 160 LOW INCOMING LINE VOLTAGE
AC Line Voltage
On the power-fail-detect-module (the sensor is not serviceable).
Maincon PCB J3 Alarm 937 INPUT LINE POWER FAULT
Electronics Temperature

On the Maincon PCB (the sensor is not serviceable).
N/A Alarm 253 ELECTRONICS OVERHEAT

Recently Viewed Items

You Have No Recently Viewed Items Yet

Visszajelzés
Haas Logo

美元价格不包括关税、报关费用、保险费、增值税及运费。
USD prices DO NOT include customs duty, customs fees, insurance, VAT, or freight.

人民币价格包含关税、报关费用、货运保险和增值税, 但不包括运费。
CNY prices include customs duty, customs fees, insurance, and VAT. DOES NOT include freight.

A Haas szállította termékek árszabása

Ez az ár tartalmazza a szállítás költségeit, valamint az export- és importtevékenységekhez kapcsolódó vámterheket, a biztosítást és minden olyan további felmerülő költséget, amely egy franciaországi helyszínre történő kiszállítást terhel, melybe Ön mint vevő beleegyezett. A Haas CNC termékek szállítása nem járhat további kötelező költségekkel.

KÖVESSE A LEGÚJABB HAAS TIPPEKET ÉS TECHNOLÓGIÁT…

Regisztráljon most!   

HAAS TOOLING ACCEPTS THE FOLLOWING:

  • Szerviz és támogatás
  • Tulajdonosok
  • Szervizkérés
  • Kezelési utasítások
  • Haas alkatrészek
  • Forgóasztal javításkérés
  • Útmutatók előtelepítése
  • Szerszámok vásárlása
  • Új Haas kiépítés és ár
  • Elérhető készlet
  • Haas árlista
  • CNCA finanszírozás
  • A Haas cégről
  • DNSH nyilatkozat
  • Álláslehetőségek
  • Tanúsítványok és biztonság
  • Lépjen velünk kapcsolatba
  • Történet
  • Szerződési feltételek
  • Haas Tooling - Szerződési feltételek
  • Adatvédelem
  • Jótállás
  • Haas közösség
  • Haas tanúsítási program
  • Haas Motorsports
  • Gene Haas Foundation
  • Haas technikai oktató közösség
  • Események
  • Csatlakozzon a beszélgetéshez
  • Facebook
  • X
  • Flickr
  • YouTube
  • LinkedIn
  • Instagram
  • TikTok
© 2025 Haas Automation, Inc. - CNC szerszámgépek

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

2800 Sturgis Rd., Oxnard, CA 93030 / Toll Free: 800-331-6746
Phone: 805-278-1800 / Fax: 805-278-2255