MyHaas Vitajte,
!
Haas Tooling História objednávok hosťa MyHaas/HaasConnect Prihlásiť sa Zaregistrovať Haas Tooling Môj účet Order History Return History MyHaas/HaasConnect Odhlásiť sa Vitajte, Moje stroje Najnovšia činnosť Moje cenové ponuky Môj účet Moji používatelia Odhlásiť sa
Nájdite svojho distribútora
  1. Zvoliť jazyk
    1. English
    2. Deutsch
    3. Español - España
    4. Español - Méjico
    5. Français
    6. Italiano
    7. Português
    8. Český
    9. Dansk
    10. Nederlands
    11. Magyar
    12. Polski
    13. Svenska
    14. пост-советский
    15. Türkçe
    16. 中文
    17. Suomi
    18. Norsk
    19. الإنجليزية
    20. български
    21. Hrvatski
    22. Ελληνικά
    23. Română
    24. Slovenský
    25. Slovenščina
    26. 한국어
    27. 日本語
Search
  • stroje Main Menu
    • Zvislé frézovačky Haas Zvislé frézovačky
      Zvislé frézovačky
      Zvislé frézovačky View All
      • Zvislé frézovačky
      • Séria VF
      • Univerzálny stroj
      • Séria VR
      • Vertikálne obrábacie centrá s výmenou paliet
      • Mini frézovačky Mini Mills
      • Formovacie stroje
      • Séria strojov pre vŕtanie/rezanie závitu/frézovanie Drill/Tap/Mill
      • Nástrojárske frézky
      • Kompaktné frézovačky
      • Séria portálových strojov Gantry
      • Mimoriadne veľké vertikálne obrábacie centrá (VMC)
      • Stolná frézka
      • Automatický nakladač obrobkov pre frézky
      • Kompaktný automatický nakladač obrobkov
    • Product Image Viacosové riešenia
      Viacosové riešenia
      Viacosové riešenia View All
      • Viacosové riešenia
      • Sústruhy s osou Y
      • 5-osové frézky
    • Sústruhy Haas Sústruhy
      Sústruhy
      Sústruhy View All
      • Sústruhy
      • Séria ST
      • Stroje s dvojitým vretenom
      • Nástrojárske sústruhy
      • Skľučovací sústruh
      • Podávač tyčí V2 Haas
      • Automatický nakladač obrobkov pre sústruhy
    • Vodorovné frézovačky Haas Horizontálne obrábacie centrá
      Horizontálne obrábacie centrá
      Horizontálne obrábacie centrá View All
      • Horizontálne obrábacie centrá
      • Kužeľ 50
      • Kužeľ 40
    • Otočné stoly a deličky Haas Otočné zariadenia a deličky
      Otočné zariadenia a deličky
      Otočné zariadenia a deličky View All
      • Otočné zariadenia a deličky
      • Otočné stoly
      • Deličky
      • 5-osové otočné stoly
      • Extra veľké otočné stoly
    • Product Image Systémy automatizácie
      Systémy automatizácie
      Systémy automatizácie View All
      • Systémy automatizácie
      • Balíky robota
      • Automatické nakladače obrobkov
      • Skupinové paletové systémy
      • Podávač tyčí Haas
      • Models
    • RÝCHLE ODKAZY Špeciálne série  Špeciálne série 
      KARIÉRA V SPOLOČNOSTI HAAS KARIÉRA V SPOLOČNOSTI HAAS ZOSTAVENIE A CENA ZOSTAVENIE A CENA CENNÍK CENNÍK NOVINKY NOVINKY VÁŠ PRVÝ STROJ CNC VÁŠ PRVÝ STROJ CNC HAAS SIX PACK HAAS SIX PACK
      NÁKUPNÉ NÁSTROJE
      • Zostavte a naceňte si stroj Haas
      • Cenník
      • Dostupné zariadenia
      • Financovanie CNCA
      CHCETE SA PORADIŤ?

      Na vaše otázky vám odpovedia a tými najlepšími alternatívami vás prevedú v podnikovej predajni spoločnosti Haas.

      CONTACT YOUR DISTRIBUTOR >
  • Voliteľné položky Main Menu
    • Product Image Vretená
      Vretená
      Vretená View All
      • Vretená
    • Product Image Meniče nástrojov
      Meniče nástrojov
      Meniče nástrojov View All
      • Meniče nástrojov
    • Product Image 4. | 5. os
      4. | 5. os
      4. | 5. os View All
      • 4. | 5. os
    • Product Image Revolvery a poháňané nástroje
      Revolvery a poháňané nástroje
      Revolvery a poháňané nástroje View All
      • Revolvery a poháňané nástroje
    • Product Image Snímanie
      Snímanie
      Snímanie View All
      • Snímanie
    • Správa triesok a chladiacej kvapaliny od spoločnosti Haas Manažment triesok a chladiacej kvapaliny
      Manažment triesok a chladiacej kvapaliny
      Manažment triesok a chladiacej kvapaliny View All
      • Manažment triesok a chladiacej kvapaliny
    • Riadenie Haas Riadenie Haas
      Riadenie Haas
      Riadenie Haas View All
      • Riadenie Haas
    • Product Image Doplnková výbava
      Doplnková výbava
      Doplnková výbava View All
      • Doplnková výbava
    • Product Image Nástroje a upnutie
      Nástroje a upnutie
      Nástroje a upnutie View All
      • Nástroje a upnutie
    • Product Image Upnutie obrobku
      Upnutie obrobku
      Upnutie obrobku View All
      • Upnutie obrobku
    • Product Image 5-osové riešenia
      5-osové riešenia
      5-osové riešenia View All
      • 5-osové riešenia
      • 5 Easy Steps to 5-Axis
    • Product Image Automatizácia
      Automatizácia
      Automatizácia View All
      • Automatizácia
    • RÝCHLE ODKAZY Špeciálne série  Špeciálne série 
      KARIÉRA V SPOLOČNOSTI HAAS KARIÉRA V SPOLOČNOSTI HAAS ZOSTAVENIE A CENA ZOSTAVENIE A CENA CENNÍK CENNÍK NOVINKY NOVINKY VÁŠ PRVÝ STROJ CNC VÁŠ PRVÝ STROJ CNC HAAS SIX PACK HAAS SIX PACK
      NÁKUPNÉ NÁSTROJE
      • Zostavte a naceňte si stroj Haas
      • Cenník
      • Dostupné zariadenia
      • Financovanie CNCA
      CHCETE SA PORADIŤ?

      Na vaše otázky vám odpovedia a tými najlepšími alternatívami vás prevedú v podnikovej predajni spoločnosti Haas.

      CONTACT YOUR DISTRIBUTOR >
  • Why Haas Main Menu
      Spoznajte zmenu vďaka spoločnosti Haas
    • Prečo Haas
    • MyHaas
    • Vzdelávacia komunita
    • Industry 4.0
    • Certifikát Haas
    • Vyhlásenia zákazníkov
  • Servis Main Menu
      Víta vás servis Haas
      DOMOV SERVISU Návody na obsluhu Postupy Ako na to Sprievodca riešením problémov Preventívna údržba Diely Haas Haas Tooling Videá
  • Videá Main Menu
  • Main Menu
    • HFO Slovakia
      HFO Slovakia
      HFO Slovakia View All
      • HFO Slovakia
      • O nás
      • Servis
      • Školenie
      • Financovanie
      • Podujatia
      • Inventár showroomu
      • Kontaktujte nás
      • Referencie zákazníkov
    • RÝCHLE ODKAZY Špeciálne série  Špeciálne série 
      KARIÉRA V SPOLOČNOSTI HAAS KARIÉRA V SPOLOČNOSTI HAAS ZOSTAVENIE A CENA ZOSTAVENIE A CENA CENNÍK CENNÍK NOVINKY NOVINKY VÁŠ PRVÝ STROJ CNC VÁŠ PRVÝ STROJ CNC HAAS SIX PACK HAAS SIX PACK
      NÁKUPNÉ NÁSTROJE
      • Zostavte a naceňte si stroj Haas
      • Cenník
      • Dostupné zariadenia
      • Financovanie CNCA
      CHCETE SA PORADIŤ?

      Na vaše otázky vám odpovedia a tými najlepšími alternatívami vás prevedú v podnikovej predajni spoločnosti Haas.

      CONTACT YOUR DISTRIBUTOR >
  • Kontaktujte nás

×

Výsledky vyhľadávania

Web Pages

Images

    • <
    • 1
    • >
MyHaas Vitajte,
!
Haas Tooling História objednávok hosťa MyHaas/HaasConnect Prihlásiť sa Zaregistrovať Haas Tooling Môj účet Order History Return History MyHaas/HaasConnect Odhlásiť sa Vitajte, Moje stroje Najnovšia činnosť Moje cenové ponuky Môj účet Moji používatelia Odhlásiť sa
Nájdite svojho distribútora
  1. Zvoliť jazyk
    1. English
    2. Deutsch
    3. Español - España
    4. Español - Méjico
    5. Français
    6. Italiano
    7. Português
    8. Český
    9. Dansk
    10. Nederlands
    11. Magyar
    12. Polski
    13. Svenska
    14. пост-советский
    15. Türkçe
    16. 中文
    17. Suomi
    18. Norsk
    19. الإنجليزية
    20. български
    21. Hrvatski
    22. Ελληνικά
    23. Română
    24. Slovenský
    25. Slovenščina
    26. 한국어
    27. 日本語
Search
×

Výsledky vyhľadávania

Web Pages

Images

    • <
    • 1
    • >

UMC - Pallet Pool - Installation

Domovská stránka pre servis Postupy UMC - Pallet Pool - Installation

UMC - Pallet Pool - Installation

– Preskočiť na sekciu – Back to Top

3.4 UMC-1000 PP Version 1

Recently Updated Last updated: 08/04/2022

UMC-1000 Pallet Pool - Version 1 - Installation


Introduction

The following procedure will show you how to install a Pallet Pool on a UMC-1000 machine.

The Next Generation software on the machine must be version 100.19.000.1110 or higher.

The Pallet Pool option is currently not field installable.

Important: To ensure that the Pallet Pool does not become mis-aligned, it is recommended that the machine and Pallet Pool be anchored. Refer to the following link: Anchoring Instructions.

The Pallet Pool option has 8 pallet stations plus 1 pallet in the machine. A maximum of 9 pallets can be installed on a UMC-1000 with the Pallet Pool option.

The Pallet Pool has 2 servo axes. The PR axis rotates the Pallet Pool ram and the PS axis extends and retracts the Pallet Pool ram to load/unload the pallets.

The UMC-1000 must be level before the Pallet Pool can be installed. Refer to the UMC-1000 Installation procedure.

To level the machine without the Pallet Pool connected to the machine, do the following: 

Make sure that there is a shorting block [1] installed on the top two pins of the P12 connector on the I/O PCB 

Make sure there is a jumper (P/N 33-0527) [2] connected to I/O PCB at P14.
 Note: These jumpers are needed to operate the machine without the Pallet Pool.

Disable the pallet pool, change setting 382 Disable Pallet Changer to Pallet Pool.


Note: The above step will disabled the Pallet Pool to allow you to zero return the machine so it can be leveled.

Refer to the UMC-1000 Installation procedure.

Leveling Screws Hardware

Note: The washers [1] and nuts [2] are installed during shipping and should be saved for installation and not be discarded.

Note: The washer orientation [3] is important.  The conical part of the washer should be against the casting,  see illustration.

Pallet Pool - Remove Shipping Brackets

   

1

Remove the loading station door blocking bolt [1].

Make sure to raise all of the pallet shelf supporting screws [2] before placing the pallet pool on the floor. 

2

Remove the bolts [1] that secure the Pallet Pool shipping bracket [2].

Remove the shipping bracket [2].

 

Pallet Pool - Placement

1

Install the Pallet Pool alignment blocks onto the host machine's base.

Note: The alignment block with the radius [1] must be installed towards the front of the UMC and the alignment block with the flat side [2] must be installed towards the rear of the machine.

Install the alignment bars [3] onto the pallet pool base.

Use the forklift or the pallet jack to place the pallet pool on the right side of the host machine.

Move the pallet pool assembly so the alignment arms are 3 - 6” (76 - 152 mm) away from the alignment blocks. 

Install the leveling pads under the pallet pool and lower the pallet pool. 

2

Install the turnbuckles [3] with the provided hardware (SHCS, washer, and bushings [1]) onto the alignment arms [2] and the base casting [4].

Evenly tighten the turnbuckles until the alignment arms mate with the alignment blocks.

UMC - Version 1 Pallet Pool HPU - Installation

1

If the pallet pool has the HPU located under the pallet pool itself, skip to the UMC- Version 2 Pallet Pool HPU - Installation section.

2

Install the HPU assembly [1] on top of the rear enclosure frame [2].

Install the HPU mounting bolts [3].

3

Wire the HPU.

  • Route the hydraulic pressure sensor cable from the control cabinet to the HPU and connect the hydraulic pressure sensor on the back of the HPU manifold.
  • Route the Pallet Pool lift and lower solenoid cables from the control cabinet to the HPU and connect it to the coils on the Pallet Pool Lift/Lower solenoid that is located on the side of the HPU manifold. Note: Connect the Pallet Pool Lift cable to the outer coil and the Pallet Pool Lower cable to the inner coil.
  • Route the Pallet Clamp solenoid cable from the control cabinet to the HPU and connect it to the coil on the Pallet Clamp/Unclamp solenoid. 
  • Route the HPU power cable from the HPU to the control cabinet and connect it to the P1 on the TMD PCB.
  • Route the HPU Oil Temperature sensor cable from the HPU to the control cabinet and connect it to the P46 on the SIO PCB.
  • Route the HPU Oil Level Sensor cable from the HPU to the connector bracket [2] and connect it to the HPU Oil Level sensor plug.  

4

Route the Pallet Clamp [1] and the Pallet Unclamp [2] hydraulic lines from the back of the B anc C axes assembly to the HPU manifold and connect to the corresponding ports.

Route the Pallet Pool Lift [3] and Pallet Pool Lower [4] hydraulic lines from the pallet pool to the HPU manifold and connect to the corresponding ports. 

NOTE: The lower port is the hole closes to the edge of the lift/lower cylinder.  

UMC - Pallet Pool - Electrical Connections

1

The following procedure will show you how to connect the electrical connections to the UMC-1000.


 Note: The PR (Pallet Rotate) and PS (Pallet Slide) amps are already installed at the factory.

Turn [OFF] the main circuit breaker and wait until the Vector Drive High-Voltage light turns off.

Knock out the pre-cut access panel [1].
Route the pallet pool cables [2] into the control cabinet as shown in the illustration.
Connect the PR motor encoder cable to Maincon PCB channel 15
Connect the PS motor encoder cable to Maincon PCB channel 16.
Connect the PR motor power cable to the amplifier labeled PR. Install the ferrite filter bead on the motor power cable.

Connect the PS motor power cable to the amplifier labeled PS. Install the ferrite filter bead on the motor power cable.

2

Remove the shorting block from the P12 connector on the I/O PCB.

Route the aux front panel cable (P/N 33-0424A) [1] from the Pallet Pool and connect it to the P12 on the I/O PCB.

Remove jumper (P/N 33-0527) [2] from I/O PCB at P14. Route the Pallet Pool status cable (P/N 33-0427) from the Pallet Pool and connect it to the I/O PCB at P14 [3].

Connect pallet alarm cable [4] (P/N 33-0482) to the I/O PCB at P50.
Make sure all the Pallet Pool status bracket connectors are plugged into the correct location.

 NOTE: Store the Pallet Pool jumpers in a safe location, these will be used by the service personnel to move or service the machine.

Enable Pallet Pool

Do the following to enable the pallet pool option on a UMC-1000.  

Important:  You will need to do this step if you perform a option 5 clean install option on a UMC-1000 with a pallet pool.

Set setting 382 Disable Pallet Changer to None.

Find the Haas Pallet Pool Parameters decal on the E-Stop on the Pallet Pool machine.  Write down the values.

Use the USB Service key to go into Service Mode.

Press [DIAGNOSTIC] Go to the PARAMETERS> Factory setting tab.

Set the following factory settings values:

  • 15.004 [:] PR-Axis Disable = False
  • 16.004 [16:3] PS-Axis Disabled = False
  • 16.078 PS-Axis Tool Change Offset = Use the decal value.
  • 15.078 PR-Axis Tool Change Offset = Use the decal value.15.140 PR-Axis Grid Offset = Use the decal value.
  • 16.140 PS-Axis Grid Offset = Use the decal value.
    • Zero Return after the grid offset is adjusted
  • 2128 [:] Pallet Pool Type = HPU Lift

Assigning Missing Pallets on Scheduler

1

It is a possible to enter a condition where the shelves in the pallet scheduling page are not assigned [1]. This will not allow the PR and PS to zero return or recover the machine. 

This section will explain how to assign the missing shelves, if your machine is not in this condition please skip to the next section. 

First, press [CURRENT COMMANDS] and navigate to the Pallet Schedule Table tab.

NOTE: The VF-2SSYT 3 Station Pallet Pool was used to create the images, but the same process will apply for all pallet pool machines. 

2

Press [EMERGENCY STOP] [1] and highlight the shelf tab on pallet number one.

With [EMERGENCY STOP] pressed, type the letter A and press [ENTER]. This will assign shelf A to pallet number 1 [2].

3

Repeat the previous step for the remaining pallet numbers in alphabetical number [1].

NOTE: The shelves can be re-assigned at any point  however the user chooses by repeating the same process (e.g. pallet number 3 can be assigned shelf B).

 

UMC - Pallet Pool - Leveling and Alignment

1

Use a bubble level [1] to roughly level the pallet pool before making any pallet changes. Steps 5 and 6 cover leveling in more detail.

2

Insert the Service Key USB and put the machine in Service Mode.

Make sure there are no obstructions inside the machine or inside the pallet pool area. Pull out all the [E-STOPS] and [RESET] the alarms.

Type [PS], press [ZERO RETURN] and press [SINGLE]. The machine will zero return PS-axis.

Type [PR], press [ZERO RETURN], and press [SINGLE]. The machine will zero return PR-axis.

Press [ZERO RETURN] and then press [ALL]. The machine will zero return all the axes.

Once all the axis are zero returned press [RECOVER]. A pop up box will appear, select [2] for Pallet Changer Recovery.

3

The Pallet Changer Recovery screen shows the Pallet Pool Status. Make sure the Pallet Lifter is Down [1]. If not press [ALTER] to bring the Pallet Lifter down.

Press [J] and then the [DELETE] button. This will rotate the pallet lifter towards station J.

 

4

Adjust the pallet pool slider by jogging the PS or PR axis so the forks align correctly underneath the pallet. This can be done by pressing [+Z] for Pallet Slide Axis and pressing [-Z] for Pallet Rotate Axis on the pallet recovery page.

With the RAM extended and the pallet over the Pallet Receiver adjust the C axis so the pins on the receiver line up with the holes on the pallet. Raise and lower the pallet using the [ALTER] on the Pallet Recovery Page until the pallet falls smoothly onto the dowels on the receiver. Record the C-axis position in Parameter 7.310.

NOTE: This is the position that the C-axis will rotate to during a pallet change operation.

Go to Factory Settings 2136 [:] Shelf J Slide Offset and 2146 [:] Shelf J Rotary Offset, and make sure the values match the PS and PR axis position, if they do not update the values.

NOTE: You can use the provided gap gauge 25-14354 as a straight edge to verify the side is flush with the end of the pallet. 

5

With the Pallet Pool in the down position, use the Gap Gauge [1] 25-14354 to set the gap by adjusting the height of the Pallet Pool.  See step 6 for more details on how to adjust the height. 

The Distance between the pins on the forks and the bottom of the Pallet surface should be the thickness of the Gap Gauge (.054") at all 4 pins, to set the gap the leveling screws will need to be adjusted.  See step 6 for more details on how to adjust the gap. 

6

The gap gauge must be touching the pins and the bottom of the pallet [1].

To do so adjust the leveling screws [2] that correlated to the pin in the same position.

For example when setting the gap of the top left pin (using the same image orientation) adjust the top left leveling screw. Continue adjusting the leveling screws in the same fashion to adjust the gap for each pin.

7

Lower the support feet until they touch the ground. 

The pallet lifter should be raised. 

Press the [INSERT] button to return the slide home.

Press the letter [A] and then [DELETE] button. This will rotate the pallet lifter to the A station.

Select the pallet slide axis use the RJH slowly jog the PS axis towards the A station.

Verify that the Pallet Pool will pick up and drop off the pallet at the A station.

Test the pick up / drop off operation on the remaining stations by using the pallet pool recovery functions. 

NOTE: If the station tray has been adjusted and it sounds like the pallet is sliding into the pin holes, adjust the feet to make sure it falls into place smoothly

Install the anchors.

Install the Pallet Pool guard panels.

Go to the Pallet Schedule Table and press [F3] to put away the pallet from the load station. 

Load the remaining pallets using the load station.

8

Place the provided tote under the Pallet Pool coolant discharge tray to catch the coolant that drains from the pallets.

Empty the tote as needed. 

NÁJSŤ DISTRIBÚTORA
Odozva
Haas Logo

美元价格不包括关税、报关费用、保险费、增值税及运费。
USD prices DO NOT include customs duty, customs fees, insurance, VAT, or freight.

人民币价格包含关税、报关费用、货运保险和增值税, 但不包括运费。
CNY prices include customs duty, customs fees, insurance, and VAT. DOES NOT include freight.

Cena spoločnosti Haas za dodanie

Táto cena zahŕňa náklady na prepravu, vývozné a dovozné clá, poistenie a akékoľvek ďalšie výdavky, ktoré sa vyskytnú počas prepravy na miesto vo Francúzsku dohodnuté s vami ako kupujúcim. Žiadne ďalšie povinné náklady nemožno pridať k dodávke CNC produktu Haas.

DRŽTE KROK S NAJNOVŠÍMI TIPMI A TECHNOLÓGIAMI OD SPOLOČNOSTI HAAS

Prihláste sa na odber!   

HAAS TOOLING ACCEPTS THE FOLLOWING:

  • Servis a podpora
  • Vlastníci
  • Požiadať o servis
  • Návody na obsluhu
  • Diely Haas
  • Žiadosť o opravu otočného zariadenia
  • Sprievodcovia prípravy inštalácie
  • Nákupné nástroje
  • Zostavenie a cena nového zariadenia Haas
  • Dostupné zariadenia
  • Cenník Haas
  • Financovanie CNCA
  • Informácie o spoločnosti Haas
  • Pracovné príležitosti
  • Certifikáty a bezpečnosť
  • Kontaktujte nás
  • História
  • Obchodné podmienky
  • Podmienky a pravidlá pre Haas Tooling
  • Ochrana osobných údajov
  • Záruka
  • Komunita Haas
  • Certifikačný program Haas
  • Motošport Haas
  • Nadácia Gene Haas Foundation
  • Komunita technického vzdelávania spoločnosti Haas
  • Podujatia
  • Zapojte sa do diskusie
  • Facebook
  • Twitter
  • Flickr
  • YouTube
  • LinkedIn
  • Instagram
  • TikTok
© 2023 Haas Automation, Inc – CNC obrábacie stroje

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.


2800 Sturgis Rd., Oxnard, CA 93030 / Toll Free: 800-331-6746
Phone: 805-278-1800 / Fax: 805-278-2255

Oznámenie o súboroch cookie

Používame súbory cookie na zlepšenie vašej používateľskej skúsenosti. Naše oznámenie o súboroch cookie opisuje, ktoré súbory cookie používame, prečo ich používame a ako môžete o nich nájsť ďalšie informácie. Potvrďte, že súhlasíte s tým, že používame analytické súbory cookie. Ak nesúhlasíte, stále môžete používať našu webovú stránku s obmedzeným používaním.

Spravovať nastavenia

Oznámenie o súboroch cookie

Používame súbory cookie na zlepšenie vašej používateľskej skúsenosti. Naše oznámenie o súboroch cookie opisuje, ktoré súbory cookie používame, prečo ich používame a ako môžete o nich nájsť ďalšie informácie. Potvrďte, že súhlasíte s tým, že používame analytické súbory cookie. Ak nesúhlasíte, stále môžete používať našu webovú stránku s obmedzeným používaním.

Functional Cookies

Analytics Cookies