10.1 VR - Specific Settings

Introduction

This page gives detailed descriptions of the settings that control the way that your machine works.

List of Settings

Inside the SETTINGS tab, the settings are organized into groups. Use the [UP] and [DOWN] cursor arrow keys to highlight a setting group. Press the [RIGHT] cursor arrow key to see the settings in a group, . Press the [LEFT] cursor arrow key to return to the setting group list.

To quickly access a single setting, make sure the SETTINGS tab is active, type the setting number, and then press [F1] or, if a setting is highlighted, press the [DOWN] cursor.

Some settings have numerical values that fit in a given range. To change the value of these settings, type the new value and press [ENTER]. Other settings have specific available values that you select from a list. For these settings, use the [RIGHT] cursor to display the choices. Press [UP] and [DOWN] to scroll through the options. Press [ENTER] to select the option.

Setting Number  Description
378 Safe Zone Calibrated Geometry Reference Point X
379 Safe Zone Calibrated Geometry Reference Point Y
380 Safe Zone Calibrated Geometry Reference Point Z
408 Exclude Tool From Safe Zone
Setting Number Description
1 Auto Power Off Timer
2 Power Off at M30
4 Graphics Rapid Path
5 Graphics Drill Point
6 Front Panel Lock
8 Prog Memory Lock
9 Dimensioning
10 Limit Rapid at 50%
15 H and T Code Agreement
17 Opt Stop Lock Out
18 Block Delete Lock Out
19 Feedrate Override Lock
20 Spindle Override Lock
21 Rapid Override Lock
22 Can Cycle Delta Z
23 9xxx Progs Edit Lock
27 G76 / G77 Shift Dir.
28 Can Cycle Act w/o X/Y
29 G91 Non-modal
31 Reset Program Pointer
32 Coolant Override
33 Coordinate System
34 4th Axis Diameter
35 G60 Offset
36 Program Restart
39 Beep @ M00, M01, M02, M30
40 Tool Offset Measure
42 M00 After Tool Change
43 Cutter Comp Type
44 Min F Radius CC%
45 Mirror Image X Axis
46 Mirror Image Y Axis
47 Mirror Image Z Axis
48 Mirror Image A Axis
52 G83 Retract Above R
53 Jog w/o Zero Return
56 M30 Restore Default G
57 Exact Stop Canned X-Y
58 Cutter Compensation
59 Probe Offset X+
60 Probe Offset X-
61 Probe Offset Y+
62 Probe Offset Y-
63 Tool Probe Width
64 Tool Offset Measure Uses Work
71 Default G51 Scaling
72 Default G68 Rotation
73 G68 Incremental Angle
74 9xxx Progs Trace
75
 9xxx Progs Single BLK
76 Tool Release Lockout
77 Scale Integer F
79 5th-Axis Diameter
80 Mirror Image B Axis
81 Tool At Power Up
82 Language
83 M30/Resets Overrides
84 Tool Overload Action
85 Maximum Corner Rounding
86 M39 Lockout
87 Tool Change Resets Override
88 Reset Rests Override
90 Max Tools To Display
101 Feed Override -> Rapid
103 Cyc Start/Fh Same Key
104 Jog Handle to SNGL BLK
108 Quick Rotary G28
109 Warm-Up Time in Min.
110 Warmup X Distance
111 Warmup Y Distance
112 Warmup Z Distance
113 Tool Change Method
114 Conveyor Cycle Time (minutes)
115 Conveyor On-Time (minutes)
117 G143 Global Offset
118 M99 Bumps M30 Cntrs
119 Offset Lock
120 Macro Var Lock
130 Tap Retract Speed
131 Auto Door
133 Repeat Rigid Tap
142 Offset Chng Tolerance
143 Machine Data Collection Port
144 Feed Override -> Spindle
155 Load Pocket Tables
156 Save Offsets with Program
158 X Screw Thermal Comp%
159 Y Screw Thermal Comp%
160 Z Screw Thermal Comp%
162 Default To Float
163 Disable .1 Jog Rate
164 Rotary Increment
165 Ssv Variation (RPM)
166 Ssv Cycle
188 G51 X Scale
189 G51 Y Scale
190 G51 Z Scale
191 Default Smoothness
196 Conveyor Shutoff
197 Coolant Shutoff
199 Backlight Timer
216 Servo and Hydraulic Shutoff
238 High Intensity Light Timer (minutes)
239 Worklight Off Timer (minutes)
240 Tool Life Warning
242 Air Water Purge Interval
243 Air Water Purge On-Time
245 Hazardous Vibration Sensitivity
247 Simultaneous XYZ Motion in Tool Change
249 Enable Haas Starup Screen
250 Mirror Image C Axis
251 Subprogram Search Location
252 Custom Subprogram Search Location
253 Default Graphics Tool Width
254 5-Axis Rotary Center Distance
255 MRZP X Offset
256 MRZP Y Offset
257 MRZP Z Offset
261 DPRNT Store Location
262 DPRNT Destination File Path
263 DPRNT Port
264 Autofeed Step Up
265 Autofeed Step Down
266 Autofeed Minimum Override
267 Exit Jog Mode After Idle TIme
268 Second Home Postion X
269 Second Home Position Y
270 Second Home Position Z
271 Second Home Position A
272 Second Home Position B
273 Second Home Position C
276 Workholding Input Monitor
277 Lubrication Cycle Interval
291 Main Spindle Speed Limit
292 Door Open Spindle Speed Limit
293 Tool Change Mid Position X
294 Tool Change Mid Position Y
295 Tool Change Mid Position Z
296 Tool Change Mid Position A
297 Tool Change Mid Position B
298 Tool Change Mid Position C
300 MRZP X Offset Master
301 MRZP Y Offset Master
302 MRZP Z Offset Master
303 MRZP X Offset Slave
304 MRZP Y Offset Slave
305 MRZP Z Offset Slave
306 Minimum Chip Clear Time
310 Min User Travel Limit A
311 Min User Travel Limit B
312 Min User Travel Limit C
313 Max User Travel Limit X
314 Max User Travel Limit Y
315 Max User Travel Limit Z
316 Max User Travel Limit A
317 Max User Travel Limit B
318 Max User Travel Limit C
323 Disable Notch Filter
325 Manual Mode Enabled
330 MultiBoot Selection Time out
335 Linear Rapid Mode
356 Beeper Volume
357 Warm Up Cycle Start Idle Time
369 PulseJet Injection Cycle Time
370 PulseJet Single Squirt Count
372 Parts Loader Type
375 APL Gripper Type
376 Light Curtain Enable
377 Negative Work Offsets
378 Safe Zone Calibrated Geometry Reference Point X
379 Safe Zone Calibrated Geometry Reference Point Y
380 Safe Zone Calibrated Geometry Reference Point Z
381 Enable Touchscreen
382 Disable Pallet Changer
383 Table Row Size
389 Vise Unclamped Safety Check
396 Enable / Disable Virtual Keyboard
397 Press and Hold Delay
398 Header Height
399 Header Tab
400 Pallet Ready Beep Type
403 Change Popup Button Size
408 Exclude Tool From Safe Zone
409 Default Coolant Pressure
416 Media Destination
420 ATC Button Behavior
421 General Orient Angle
422 Lock Graphics Plane
423 Help Text Icon Size
424 Mist Extractor Condenser Time Out
430 Enable - Broken Tool Detection
431 Region of Interest - Broken Tool Detection
433 Behavior - Broken Tool Detection